TURNIGYのマイクロモータ14から03 5100kv

• Overall
• Quality
• Value

Customer Rated

May 18, 2011

type 1403 ha gazou toha tigau

imoneji ga naku koteisiki de daikara ha motor wo hazusenai

motor kara deteiru sen ha hosoi enamerusen de gazou no youna

hifukusen dehanai

• Overall
• Quality
• Value

Customer Rated

Apr 25, 2011

Received two of these small motors today. The picture on the website shows three colored wires (Red, Black, White) covered with insulated tubing. The product I received today does not have any covered ESC wires. Instead I have three exposed single stranded copper wires which are very fragile and I will have to cover myself. This is the first time I have been dissapointed with a purchase from Hobby King. I did NOT receiving the product in the picture on the website.

• Overall
• Quality
• Value

Customer Rated

Mar 27, 2011

Bought 2. One came with shrinktubed leads, other with longer but plain wires. One shaft i pushed out easily with the prop. And both motor is shaking only, they do not work with any esc any timing. It might be bad luck but seems there is no quality control at all.

• Overall
• Quality
• Value

Customer Rated

Mar 04, 2011

14-03????????????????????????????????????????????????3????????????????????????????

??????????????????????????

• Overall
• Quality
• Value

Certified Buyer Rated

Sep 08, 2010

It is a very good motor once in the air, however my casing wasn't tight to the shaft so it could slide around and I couldn't get my prop on because it just pushed the shaft in. Also when soldering plugs on to the wires, the wire came off and had to be soldered back on. But then they broke off again! this time the solder did not come apart the winding broke off and I couldn't solder the wire back on. so now I have had to order a new on. in its favor it is cheap enough to buy another on I hope my experience with the next on is better.

• Overall
• Quality
• Value

Customer Rated

Aug 26, 2010

25/08/10

Purchase 1, then 8 weeks later another, BIG diffrence between the 2, First 1 perfect, 2nd glue everywhere, on sharft, on magnets making turning very ruff. First 1 had red insulation on end of wires, 2nd had NO red insulation and very very long wires ? The motor was very easy pull apart,( a bit to easy ) to remove the lumps of glue.

First motor, 5 stars!!!

Second motor, 3 stars for QC !!!

• Overall
• Quality
• Value

Customer Rated

May 07, 2010

Wir ohne irgenein Zubehr geliefert. Die Motorkabel sind einfach die verzinnten Kupferlackdrhte. Lieber den T1400-4500 nehmen, da ist alles dabei(Goldis!!, Schrumpfschlauch, Propsaver und Gummi)

• Overall
• Quality
• Value

Certified Buyer Rated

Sep 02, 2009

Great little motor. Lacking in the torque I wanted for my application, but a great motor regardless. Running on 1S with a 1Gram HC 3 amp esc. The mount is a lot heavier than it needs to be, but I just removed it and glued the motor into a balsa firewall I made.

• Overall
• Quality
• Value

Certified Buyer Rated

Apr 02, 2009

I need some help trying to solder bullet connectors for this one. All three wires run togther through the shrink tube, not sure if I am supposed to pull the shrink tube off and put individual pieces over each wire, or what???? Help

• Overall
• Quality
• Value

Customer Rated

Oct 28, 2008

Very lightwight Motor.

9N12P. Windings are with glue, so it is very hard to rewind it : (

Magnet glue is also very strong.

My Motor weights 5g with other winding and modyfied mount.