Jumper T12 V3 Mode 1 Transmitter w/JP4in1 Multi Protocol Transmitter Module (Black)
Jumper T12 V3 Mode 1 Transmitter w/JP4in1 Multi Protocol Transmitter Module (Black)
Copy and Share the Below URL
This is the third generation Jumper T12 Multi-Protocol Transmitter with hall sensor gimbals, it is very versatile and comes with JumperTX updated firmware (based on the OpenTX Project). There is a JR style module bay in the back that comes with the extremely versatile Jumper JP4-in-1 module that allows communication with a wide range of protocols such as Walkera DEVO, Spektrum DSM2/DSMX, Flysky, Esky, Frsky, WLtoys, Hubsan, Hisky, Futaba SFHSS Assan etc.
This release of transmitter supports TBS crossfire in CRSF mode with LUA script support without any hardware modifications. The Jumper T12 V3 also comes with the smooth V2 gimbals from the T8SG V2 to provide excellent control. The 1.7inch 128x64 LCD screen allows easy viewing for setting up your models. There are four 3-position switches, two 2-position switches and two dials for all your devices. The transmitter can use up to 12 channels depending on the receiver type.
The JP4IN1 module integrates the CC2500, NRF24L01, A7105 and CYRF6936 RF chips into one PCB. The JP4IN1 is an OpenTX original accessory which can do serial digital signal communication with the Frsky series radios. Recognizing PPM signal from radio output, then converted to the corresponding radio protocol to achieve control of the fixed wing and drone aircraft.
For supported protocols: www.jumper.xyz/t12
The Jumper T12 transmitter is easy to use and the module bay allows for lots of different protocols to be utilized.
Features:
• JumperTX (open source Firmware set based on the OpenTX Project)
• JR/FrSKY compatible module bay on the rear side
• USB online firmware upgrade
• Ultra-low power consumption, longer battery life
• Up to 16 channel output
• Open Source Firmware, all channels are fully programmable
• Multilingual menu
• Vibration reminder function
• Support telemetry (depending on the receiver)
• Crossfire CSRF Compatible
• LUA Script support
• Hall sensor gimbals
Radio Specs:
Radio MCU: STM32F205VET6 (512kb)
Size: 158x150x58mm
Weight: 342g (without battery)
Working voltage: DC5-DC9V (factory with 4 x AA battery box, 2s Lipo recommended, batteries not included)
Firmware: JumperTX (an open-source Firmware set based on the OpenTX Project)
Channels: Up to 16 channel output
Display: 1.7-inch LCD display, 128x64 resolution
Gimbal Type: Potentiometer
Upgrade method: USB online upgrade
Simulator mode: 3.5mm standard ppm output or USB HID
Voice support: Yes
Stick Mode: Mode 1
Case Color: Black
JP4-in-1 Specs:
Working voltage: 6-9V
Working current: <=100mA
Operating frequency: 2.4GHz ISM band
RF power: +22DBM
Main control chip: STM32F103CBT6 (128K ROM, 20K RAM)
Module bay compatibility: FRSky, JR and other
Dimensions: 64x49x33mm (without antenna)
Net Weight: 42g (including antenna)
Software Compatibility: Suitable for radios using OpenTX or er9x/ersky9x
Firmware updatable: Yes, via USB
Includes:
Jumper T12 V3 transmitter with module Mode 1 (Black)
Neck strap
USB cable
Instruction manual
Requires:
4 x “AA” Batteries or 2S Lipo
Please note: There is a copy of the User Manual under the "Files" tab.
Pirimidon | Verified Buyer
-
Overall
-
Quality
-
Value
Good
Sep 20, 2019
x | Verified Buyer
-
Overall
-
Quality
-
Value
JUMPER T12 V3 TRANSMITTER
Sep 15, 2019
Sascha | Verified Buyer
-
Overall
-
Quality
-
Value
Travel Radio
Aug 19, 2019
Pietro | Verified Buyer
-
Overall
-
Quality
-
Value
piccola e potente
Jul 13, 2019
Pepa | Verified Buyer
-
Overall
-
Quality
-
Value
2sLi - low consumption :-)
Jul 08, 2019
| User Manual | Download [531] |
Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!
