Totale prijs

€ 0,00

Winkelmand 0 Winkelmand 0 Loading...

2725 borstelloze Outrunner Motor 1600kv

Generating Links

2725 borstelloze Outrunner Motor 1600kv

Al gekocht Discontinued Product

Please continue searching for a similar product.
SKU:
074000063
Geen verzendkosten? Klik hier meer leren!

2725 borstelloze Outrunner Motor 1600kv

specs:
Afmetingen: 27mm x 25mm
Gewicht: 35g
KV: 1600 rpm / v
Voltage: 7,4 V ~ 11,1 V (2s ~ 3s)
Max stroom: 17A
Max Power: 190w
Shaft: 3mm

* Kleur kan variëren

  • Kv ( tpm / v ) 1600.00
  • Max Currents (A ) 17.00
  • Resistance ( mh ) 0.00
  • Max Voltage ( V ) 11.00
  • Vermogen ( W) 190.00
  • Shaft A ( mm ) 3.00
  • Lengte B ( mm ) 20.00
  • Can Diameter C ( mm ) 27.00
  • Kan Lengte D ( mm ) 10.00
  • Totale lengte E ( mm ) 45.00
attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Upload video

Registreer u om video's te uploaden aanmelden of registreren

Onderwerpen
Sorteer op
Meest recente onderwerpen
* Bijnaam:

* Uw antwoord:


Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
annuleer
Bevestig
Plaats een nieuw onderwerp
* Bijnaam:

* Uw onderwerp:



Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
Onderwerp plaatsen

Registreer u om beoordelingen te schrijven aanmelden of registreren

richard | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

Jan 21, 2015

Worked fine at first. Didn't take long to figure out there is a quality control issue with this motor. At about 3/4 throttle it came to a screeching halt. Drop throttle and start again with same results. Found out that the stator with the wire windings worked loose from the motor housing. At about 3/4 throttle it would start to spin on the housing and lose timing causing it to stop. All three of these motors i got do the same thing. So it wasnt just a fluke. I assume that separating the motor and glueing the stator on firmly will fix the issue. I am waiting for one to dry to test it.

| Geverifieerde koper

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Oct 09, 2014

good engine

put it on biks3

now learning to fly)

Evil Pusher | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

Oct 04, 2014

whatever Ive writen before - forget it - this motor is rubbish. Bearing becoming hot on 3S, one of two was burning by using an 8x6 prop. POS

Evil Pusher | Geverifieerde koper

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Sep 15, 2014

nice little outrunner - bearings seems to be okay. easy to install - like shaft on both side.

__Raju | Geverifieerde koper

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Jul 03, 2014

It is good motor but where is motor mount? draw more current, gives less thrust compared to other motors in it's size. It is not bad motor but also not very good one, something in between.

| Geverifieerde koper

  • Quality
  • Value
  • Overall

Certified Buyer Rated

May 22, 2014

Great little motor. Attached this my my makeshift hovercraft and worked a treat, plus the fact that it didn't cost a lot was a bonus.

Geoffro | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

May 09, 2014

Badly designed motor. They have decent grunt but the shaft is stupidly long at the rear and cannot be adjusted. You would think you can take the grub screws out and the housing the slide the shaft up? no.. took them apart... the stop of the shaft is fixed to the spinner, it's not sliding anywhere. They also have a chunky 4.2mm axl

Wade | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

Feb 26, 2014

I ended up with six of these. admittedly I crashed my quad and bent two of the props. But then today while hovering one of the motor shafts sheared off at the groove where the e-clip holds it on. Which by the way is where the other two bent.

Gerhard | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

Sep 17, 2013

Good motor for this price. I run it in a flying wing with 1000mm(39.4in) wingspan and
460g(14.8oz) weigth. Prop 8x4(fold). 3S 850mA lipo. Goes unlimited vertical and has
around 5min motor runtime.

vaughan | Geverifieerde koper

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Feb 20, 2013

Very nice motor although I couldn't slide the shaft through without fear of damaging it. It would need a thin firewall for attaching it behind the propeller.

  1. 1
  2. 2
Klantbestanden
DIY Hex using 2725 motors Download [156]
Upload bestand

Registreer om bestanden te uploaden.
Alstublieft aanmelden of registreren om nu hobbyisten te helpen!

Accessoires