Registreren

Product Finder

Instellingen

Useful links

 
[["US","AU","GB","DE"]]
Registreren
Shipped From:
  • Global

Corona CS238HV Analoge Metal Gear Servo 4,6 kg / 0.13sec / 22g

Corona CS238HV Analoge Metal Gear Servo 4,6 kg / 0.13sec / 22g

QTY:

Now save bewaar € 0,00 € 0,00

€ 7,27
Stock:
Gewicht:
43 g
SKU:
014000034-0

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Combine

essential items and
acc
Product
Omschrijving

Corona CS238HV Analoge Metal Gear Servo 4,6 kg / 0.13sec / 22g

Model: CS238HV
Operating Voltage: 6.0V / 7.4V
Werkende stroom: 300mA / 400mA
Operating Speed: 0.14sec.60º / 0.13sec.60º
Stall Koppel: 4kg.cm / 4.6kg.cm
Grootte: 29X13X30mm
Gewicht: 22g
Dead Band: ≤5uSec
Operating Travel: 40º / ene kant pulse reizen 400US
Potentiometer: 3 slider / Indirect Drive
Kogellager: MR106
Gear: Metal
Connector draad: 215mm
Bedrijfstemperatuurbereik: -20C + 60c

Product
Specifications

Aanvullende Informatie

  • Sku:
    014000034-0
  • Brand:
    Corona
  • Gewicht ( g)
    43.00
  • Lengte
    70.00
  • Breedte:
    30.00
  • Hoogte:
    50.00
  • Snelheid ( Sec / 60deg )
    0.13
  • Torque ( kg) ( min . 0,01 kg )
    4.60
  • Unit Weight (g):
    22
  • A ( mm ):
    35.00
  • B ( mm )
    29.00
  • C ( mm )
    31.00
  • D ( mm ):
    13.00
  • E ( mm ):
    40.00
  • F ( mm )
    20.00
Community
Discussions
Rate&
Review

Schrijf je eigen recensie

Only registered users can write reviews. Please, sign in or sign up

Quality
Value
Overall
These servos work just fine with my orange receiver and a 5 volt BEC.
The complaint I have is with the servo arms. They do not fit the metal out put shaft (spline) on the servo; the servo arm holes are too small. I had a few old arms from a full sized FMA servo and they seem to fit ok.
Quality
Value
Overall
Quality
Value
Overall
God og billig servo, momsen skal ned I DK foer vi gaar konkurs
Quality
Value
Overall
Quality
Value
Overall
These servos are great for 50-60" plane currently my servos hooked in rudder and elevator. They r high performance servos according to their cost. In short they r worth the price.
Quality
Value
Overall
Quality
Value
Overall
Sad to say I have come to the conclusion that these servos are not HV in a useable sense.
They might be HV in that they do not burn out after being connected to a 2s LIPO for 45 minutes but they develop a dose of frantic jitters at end of travel. Who wants their ailerons or elevator beating the air at full travel? This gradually decreases in intensity as the voltage is lowered. Even at 6v they are jittery to the point I would not use them.
Everything goes smooth, quiet, and stable at 5V and I would never use them at any higher voltage.
All 4 servos I purchased behave like any other standard, cheap, strong servo at 5v.
Forget the HV specification.
Quality
Value
Overall
Quality
Value
Overall
Just received 4 of these little beasts. Hooked them up to one of my Orange Futaba FAAST compatible RX's and tried them at various voltage rates. I set the RX to analog mode - 3 slow flashes. Servos are wildly jittery on 2s 7.2v Lipo, extremely jittery on 6.4v LIFE, mildly jittery with BEC set to 6v and quite good with BEC jumper set for 5V.

So useable High Voltage they are NOT. I suspect the Orange RX can be a bit noisy so will try later with FrSky RX when one is available as I have had better smoother results with them.
Quality
Value
Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Combine

essential items and
acc

Productlabels

Gebruik spaties om verschillende labels te scheiden. Gebruik enkele aanhalingstekens (') voor zinnen.