New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

F9F Panther BYR Hand Launch Version (PNF)

F9F Panther BYR Hand Launch Version (PNF)

Shipped From:
  • Global
Discontinued Product

Please continue searching for a similar product.
SKU:
F9F-2-PNP-B
WANT FREE SHIPPING? Click here to find out more!

De Grumman F9F Panther had het onderscheid van het winnen van de US Navys eerste overwinning in de skys dan Korea toen het een Yak 9 neergehaald in een lucht-lucht engagement. Ontwikkeld aan het eind van WW2, met de eerste vlucht vindt plaats in november 1947, was dit het grote kijken vliegtuigen die niet in front line service voor lang voordat ze vervangen door nieuwere geveegde vleugel ontwerpen, en eindigde zijn carrière grotendeels in de reserve squadrons. Ondanks deze korte carrière in de luchtvaart termen, de Panther heeft vele fans.

Deze zeer schaal op zoek EPO model heel erg doet de Panther rechtvaardigheid, en ziet er geweldig uit in de lucht met die enorme kleurrijke vleugel tanks. De zeer krachtige legering EDF unit levert veel stuwkracht en klinkt fantastisch, de prestaties is uitstekend, zelfs op 3s met veel verticaal. Omdat het met de hand-launch-versie geeft je de opties voor ingaand als u dat wenst als de montageplaten zijn vooraf gemonteerd. Alle hoog koppel servo vooraf gemonteerd, zoals het volledig programmeerbaar ESC en UBEC die de mogelijkheid 4.8V of 6v uitgang met de RX geeft.

Dit is een kwaliteit schaalmodel dat is een beetje meer betrokken dan de gemiddelde Plug N Fly op het gebied van bouwen, maar de beloning voor de RC piloot is een van de beste vliegende & zoek schuim modellen in de 70mm klasse.

specs:
Spanwijdte: 1050mm
Lengte: 1000mm
Flying Gewicht: 1000 ~ 1100g
EDF: Alloy 68mm met 2848 borstelloze inrunner 4370kv (Statisch Thrust op 3s - 1150g ~ 1200g)
ESC: 60A OPTO
UBEC: 3A ~ 5A
Servo: 4 x 9g High Torque

inclusief:
alle Hardware
instructies
Uitgebreide Decal Sheet

vereist:
Uw Eigen 4-kanaals TX / RX
3700mAh 3s ~ 5000mAh 3s LiPoly Battery

  • Sku F9F-2-PNP-B
  • Brand -
  • Capaciteit ( mAh ) -
  • Gewicht 3035.0000
  • Lengte 960.00
  • Packaging Width 290.00
  • Hoogte 290.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Came very well wraped, go's together fast for a kit, foam is first class but had a couple of blisters in the paint, used epoxy to glue it but be warned sand the paint before glueing, decals are nice and are on three sheets good manual with C of G. The wing is glued on so if you wont to fit retracks do it before fixing the wing though ply plates are pre fitted and servoless retracks would be easy to fit at any time. waiting for weather to maiden her it really likes the part.

I hope she flys as good as she looks

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Came very well wraped, go's together fast for a kit, foam is first class but had a couple of blisters in the paint, used epoxy to glue it but be warned sand the paint before glueing, decals are nice and are on three sheets good manual with C of G. The wing is glued on so if you wont to fit retracks do it before fixing the wing though ply plates are pre fitted and servoless retracks would be easy to fit at any time. waiting for weather to maiden her it really likes the part.

I hope she flys as good as she looks

Its a realy nice model. I changed the engine and esc with a rclander 68mm, 1.7 kg thrust and 80 amp esc. I modified it with flaps and dsr b retracts. Had to do some cutting to make it fit but it was worth it. I also put on the turnigy rc led lightning system. I use a 4 cell 4500 mah battery and a separate receiver battery. (2 cell 850 mah. life battery, 48 gram). Tot weight is 1.750 kg and flying time with different power setting is 12min.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Its a realy nice model. I changed the engine and esc with a rclander 68mm, 1.7 kg thrust and 80 amp esc. I modified it with flaps and dsr b retracts. Had to do some cutting to make it fit but it was worth it. I also put on the turnigy rc led lightning system. I use a 4 cell 4500 mah battery and a separate receiver battery. (2 cell 850 mah. life battery, 48 gram). Tot weight is 1.750 kg and flying time with different power setting is 12min.

Not a bad foamy EDF, it has a nice shiny painted finish with minimal moulding dots and lines, it can be seen that these have been avoided where possible and it looks neat. Its not smooth smooth, but its not bad for a painted foam finish.

Instructions are OK, limited though, and show assembly steps which on my model have already been completed. This did not save time at all as the assembly was pretty shoddy, parts did not fit, control surfaces were not aligned and there was a significant amount of excess glue in the hinges preventing movement. After a couple hours trimming with the dremel, I have managed to get it to work. Also note that the "perfect fit" DSRB retracts are no where near a perfect fit, and require cutting and gluing in blocks for the retracts.

I will be running 2x 3S 2150 batteries which need to be jammed all the way in the nose (past the battery tray) to get it to balance. EDF does run smooth on mine though, and will produce around 0.8-0.9:1 thrust with the retracts, and top 1-1.1:1 without the retracts.

Overall, a great looking model, great finish on the foam with sharp trailing edges on the wing (looks great). Might paint the surfaces a bit to help distinguish top and bottom.

Would I buy it again? so far I'm pretty impressed by the foam model, but let down by the poor assembly. With some work that I'm prepared to put in, at this price point, I think I

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Not a bad foamy EDF, it has a nice shiny painted finish with minimal moulding dots and lines, it can be seen that these have been avoided where possible and it looks neat. Its not smooth smooth, but its not bad for a painted foam finish.

Instructions are OK, limited though, and show assembly steps which on my model have already been completed. This did not save time at all as the assembly was pretty shoddy, parts did not fit, control surfaces were not aligned and there was a significant amount of excess glue in the hinges preventing movement. After a couple hours trimming with the dremel, I have managed to get it to work. Also note that the "perfect fit" DSRB retracts are no where near a perfect fit, and require cutting and gluing in blocks for the retracts.

I will be running 2x 3S 2150 batteries which need to be jammed all the way in the nose (past the battery tray) to get it to balance. EDF does run smooth on mine though, and will produce around 0.8-0.9:1 thrust with the retracts, and top 1-1.1:1 without the retracts.

Overall, a great looking model, great finish on the foam with sharp trailing edges on the wing (looks great). Might paint the surfaces a bit to help distinguish top and bottom.

Would I buy it again? so far I'm pretty impressed by the foam model, but let down by the poor assembly. With some work that I'm prepared to put in, at this price point, I think I

The model is ok but the retracts that are supposed to be an exact fit do no fit without triming wood at mounts and also nos has to modified to accept nose wheel electric retract. this was the TGY-DSRB retracts.

As for weight and balance try putting fiberglass in the nose to strengthen it and the balance will be fine. This has to be done before glueing it on. Tha plane is slower with the electric retracts and a better motor would be good.

Charles

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The model is ok but the retracts that are supposed to be an exact fit do no fit without triming wood at mounts and also nos has to modified to accept nose wheel electric retract. this was the TGY-DSRB retracts.

As for weight and balance try putting fiberglass in the nose to strengthen it and the balance will be fine. This has to be done before glueing it on. Tha plane is slower with the electric retracts and a better motor would be good.

Charles

Finally got it balanced. After a burnt out motor and splitting it in half twice. The alloy EDF needs a 4000mah batt up front to get the CG forward enough. Flys steady and has huge presence in the air. Sounds a million bucks and fan is smooooooth. Not really for beginners and even then I'd only take it out for special occasions. Enjoy.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Finally got it balanced. After a burnt out motor and splitting it in half twice. The alloy EDF needs a 4000mah batt up front to get the CG forward enough. Flys steady and has huge presence in the air. Sounds a million bucks and fan is smooooooth. Not really for beginners and even then I'd only take it out for special occasions. Enjoy.

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save