New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

hexTronik DT700 borstelloze Outrunner 700kv

hexTronik DT700 borstelloze Outrunner 700kv

Shipped From:
  • USA
  • Global
QTY:

Now save bewaar € 0,00 € 0,00

€ 12,62
status:
In voorraad
SKU:
DT700
WANT FREE SHIPPING? Click here to find out more!

Schijn bedriegt. Dit outrunner is ongeveer twee keer zo groot als een TowerPro bel motor, en zwaait een veel grotere prop. Zijn de gebruikte motor op een aantal van Art-techs nieuw vliegtuig kits, die testiment om zijn duurzaamheid, gebruiksgemak en kwaliteit.
De DT700 zal een 11x4.7 SF prop lekker swingen, tot meer dan 900 g stuwkracht te produceren.
Het is geweldig voor een grotere GWS foamies of parkfly vliegtuigen.

Spec.
Vereiste Voltage: 11.1V
Voorgestelde Batterij Capaciteit: 1300mAh +
Prop voorgesteld: 10x4.7, 11x3.8 of 11x4.7
Max stroomverbruik: 13 (met 11x4.7 prop)
Max stuwkracht: 900g +
Onbelast Current: 1.2A
Shaft: 4M (perfect geschikt voor Towerpor / GWS SF Slow Fly props)
Gewicht: 78g
Diameter: 41mm
Totale lengte: 77mm
Kv: 700rpm / v
Wordt geleverd met mount, zoals aangegeven in Afbeelding

Test rapport.
We gebruikten deze outrunner om de macht van de een Art-tech Pitts. Uitgevoerd met een 1300mAh 3s1p 20C pack, 18A BESC en 1147 GWS / TowerPro prop, de Art-tech pitts liep mooi. Uitstekende klim tarief, maar niet hoverable en met 13minute vluchttijden of meer, we waren erg onder de indruk.
Een zeer efficiënt outrunner voor langzamer vliegen modellen van maximaal 0,15 grootte.

  • Sku DT700
  • Brand hexTronic
  • Gewicht 79.0000
  • Lengte 88.00
  • Breedte 48.00
  • Hoogte 50.00
  • Kv ( tpm / v ) 700.00
  • Max Currents (A ) 13.00
  • Resistance ( mh ) 0.09
  • Max Voltage ( V ) 13.00
  • Vermogen ( W) 270.00
  • Shaft A ( mm ) 4.00
  • Lengte B ( mm ) 38.00
  • C Diameter ( mm ) 40.00
  • Kan Lengte D ( mm ) 10.00
  • Totale lengte E ( mm ) 78.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

very powerful bell motor, i ts almost equal in performance with a 35xx motor 920k, except that its half the price , also it can handle 4s easily, if 10-12`prop-=25amb esc
if 13 prop= 30 a esc

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

very powerful bell motor, i ts almost equal in performance with a 35xx motor 920k, except that its half the price , also it can handle 4s easily, if 10-12`prop-=25amb esc
if 13 prop= 30 a esc

Using this motor with a 30 Amp car ESC for an ROV project. So far preliminary tests are working nicely. It produces quite amount of thrust with my 57mm boat props, while submerged. the only problem I've had is that the set screws in the base seem to strip fairly easily, and I've had to drill an indent to keep the control wires from coming loos and flopping around.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Using this motor with a 30 Amp car ESC for an ROV project. So far preliminary tests are working nicely. It produces quite amount of thrust with my 57mm boat props, while submerged. the only problem I've had is that the set screws in the base seem to strip fairly easily, and I've had to drill an indent to keep the control wires from coming loos and flopping around.

It's a good product. It works as it should be.

Two thumbs up. I would like to recommend it to all user.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

It's a good product. It works as it should be.

Two thumbs up. I would like to recommend it to all user.

cheap work well and very efficient. the one and only down side is I have had 2 out of 4 have magnets come loose. I hope hk can in prove on their quality of products.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

cheap work well and very efficient. the one and only down side is I have had 2 out of 4 have magnets come loose. I hope hk can in prove on their quality of products.

These motors are ok for scratchbuild multirotors, but you will soon find they are a bit sluggish. You need to epoxy the wires which I am sure has been stated, but I ruined two motors before I did it correctly. I used Amazing Goop for ease. I have these on an h-quad, but they make a lot of vibration. I think all bells have that as they have such a small support, but large bell. For the price I'm sure you can find better motors that spin freely and have no need for modification.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

These motors are ok for scratchbuild multirotors, but you will soon find they are a bit sluggish. You need to epoxy the wires which I am sure has been stated, but I ruined two motors before I did it correctly. I used Amazing Goop for ease. I have these on an h-quad, but they make a lot of vibration. I think all bells have that as they have such a small support, but large bell. For the price I'm sure you can find better motors that spin freely and have no need for modification.

Good motors ....for the price....the issue is you can't really tighten props as if you try to screw the props too tight the shaft has a tendency to slip and cause the end ring clip to push against the bottom bearing causing the motor to run like its a bit jammed...gummy feel...I would go for the zip tie method to mount props....better bearings would be great....and neater windings would make this a killer deal....I don't think patrons would mind paying a couple of dollars more for this...all in all it is a great motor for a cheap not so trusty multicopter

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good motors ....for the price....the issue is you can't really tighten props as if you try to screw the props too tight the shaft has a tendency to slip and cause the end ring clip to push against the bottom bearing causing the motor to run like its a bit jammed...gummy feel...I would go for the zip tie method to mount props....better bearings would be great....and neater windings would make this a killer deal....I don't think patrons would mind paying a couple of dollars more for this...all in all it is a great motor for a cheap not so trusty multicopter

Superb item to use in all RC stuff. Just safe peace of mind that you have a tad better item in your gear. Buy with confidence

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Superb item to use in all RC stuff. Just safe peace of mind that you have a tad better item in your gear. Buy with confidence

good motor, altough winding is not the best quality.

If you crash your plane and shaft bends, there is no replacement parts for it.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

good motor, altough winding is not the best quality.

If you crash your plane and shaft bends, there is no replacement parts for it.

best brushless motors for my projects period, I have too many of them now.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

best brushless motors for my projects period, I have too many of them now.

I have four of these DT700 motors and have used them on a tricopter preceding the quadcopter. I used these with the 11x4.7 sf props. They are good motors for the money but are a bad long term investment. They do what you want in the short run but if you are looking to go out and fly a multicopter and not worry about having a motor bearing go bad or the set screw loosen during flight or the balance being off, I would advise not to buy these motors.

If your going to build a multicopter, buy durable long lasting motors that will keep you on the flying field instead of in the workshop. Buy a quality set of motors. quality motors will most likely cost around $20-$30 per motor, especially if your using looking to get aerial footage and have a lot of expensive equipment on your multicopter. This may seem steep and I'm sure people will attest that their DT700 or DT750's work great, and good for them, but your going to spend the money either on a replacement or on bearings which will total to about the ammount of quality motors.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I have four of these DT700 motors and have used them on a tricopter preceding the quadcopter. I used these with the 11x4.7 sf props. They are good motors for the money but are a bad long term investment. They do what you want in the short run but if you are looking to go out and fly a multicopter and not worry about having a motor bearing go bad or the set screw loosen during flight or the balance being off, I would advise not to buy these motors.

If your going to build a multicopter, buy durable long lasting motors that will keep you on the flying field instead of in the workshop. Buy a quality set of motors. quality motors will most likely cost around $20-$30 per motor, especially if your using looking to get aerial footage and have a lot of expensive equipment on your multicopter. This may seem steep and I'm sure people will attest that their DT700 or DT750's work great, and good for them, but your going to spend the money either on a replacement or on bearings which will total to about the ammount of quality motors.

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. ...
  7. 9
Customer files
better_way_for_screws Download [30]
DT700 on homebuilt Karbon-X Frame Download [278]
DT700 on homebuilt Karbon-X Frame Download [287]
Custom motor mount Download [126]
No File Name Download [48]
Winding1 Download [847]
Winding2 Download [754]
Winding3 Download [772]
DT700 vs L2210-1650 data set Download [24]
DT700 vs L2210-1650 data set Download [24]
  1. 1
  2. 2
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!