Bestuurd door een Atmel Mega168PA 8-bits RISC gebaseerde microcontroller en gebruik een 3-assige MEMS gyro de Hobbyking i86 Multi-Rotor van toezicht kan 8 Multi-rotor craft types en 2 modi vlucht zonder dat de microcontroller knipperen . De eenvoudige dip switch systemen zorgt voor een snelle en eenvoudige selectie van uw gewenste Multi-rotor configuratie en flight mode.
Licht van gewicht en compact de i86 kan passen in de kleinste van ambachtelijke en bevat een klein stukje dubbelzijdig plakband te installeren.
De Hobbyking i86 Multi-Rotor Control Board ondersteunt:
Aero (vaste vleugel)
Alle bovenstaande functies kunnen worden ingesteld in "Normal" mode of "Sport" -modus (standaard normaal)
Input Voltage: 4v 6V
Ingangssignaal: 50hz standaard PPM
PWM Frequentie: 400Hz voor ESC, 50hz voor servo's
Gyro schaal: +/- 500dps, ODR: 800Hz
Operating temp: -40 ° C tot 85 ° C
Maat: 40mm x 40mm
Gewicht ( g)
great price too took only a few minutes to set up
highly recommend this
board really good for filming with pots around 75pcnt
not so great for acro unless update firmware which is easily done with a usb asp i brought 2 !Works well ! Quick and easy setup, good price!Couldn't get it to work properly, even though, i did everything manual said. It starts shaking before you take off the ground. Maybe I didn't have enough experience with gain adjustment, but this was how I crashed my first quad...
I used it in st360 with multistar 20A ESCs and corona receiver.
Everything apart from shaking seems to be okCan't quite believe I missed this important bug when disarming. I nearly got a 11" prop at full speed in the eye and it has ruined my 3 DT750 motors.
Please do not be complacent like I was, this board has not been fixed since all the bad reports regarding the disarm bug. DO NOT USE IT FOR MULTIROTORs. I don't care that it only seems to do it for SimonK ESCs, this is just not acceptable safe programming of a flight controller. I will be asking for my money back and money for the 3 DT750s. Sorry HK, you simply are playing with fire by selling these boards.Couldn't make my Y-6 fly stable with it - was almost uncontrollable with whatever tune-ups I've tried. Replaced with KK2.1 and on the 1st flight copter hovered in the middle of the room with my hands down. There are much better boards now than this one.awesome controller , very flexible , easy to setup with dip switches , very stable
a good place to start in quadcopters
really chesp a great alternative to the kk board
a great budget board once set up. mine was a bit tricky as it turned out the motor diagram was wrong. motor 2 should be motor 1, 3 = 2, 4 = 3, 1 = 4, once that was sorted it all worked fine, only rudder needed reversing on the tranny, so for the maiden, stable in the hover, just a slight drift to the right. I can correct that with a bit of sub trim. so a great budget board to start flying multi rotor machinesI got two of these for a project quad. Works pretty well and easy to use. It just takes a little patience with the pitch, yaw, and roll pots. Once you have them set, quad flies very well.Little bit complicated to get working properly, but nice to fly when done properly. No self leveling feature, but good for training maneuvers and orientation. Nice and very cheap controller.
HK i86 User Manual download now [933kb] Tips montajes download now [3731kb] So simple 1 download now [170kb] No File Name download now [790kb] rus review download now [0kb] Manual_Rus download now [1176kb] HK i86 manual download now [933kb] i86 Stick Centering corrected download now [7811kb] No File Name download now [396kb] No File Name download now [933kb] No File Name download now [933kb]