HobbyKing ™ Mi Digital Servo HV / MG 11.8kg / 0.06sec / 61g

• Overall
• Quality
• Value

Customer Rated

Dec 01, 2014

I have bought 15 of this servo. I use them in all my touring cars, and have sold it to most of my friends in the local club. 2 has failed, one did not work and one failed after short time use. I still use my oldest ones, they have now been in use for over 2 years. Only remember to adjust the endpoints, if not adjusted, the servo will be not work very long. If correctly adjusted, you have the servo for a loooooong time :-)

• Overall
• Quality
• Value

Customer Rated

Apr 26, 2014

Gears are to weak ,ripped of the teeth after 10 minutes ,only used as a brake servo in a big scale car.

• Overall
• Quality
• Value

Customer Rated

Mar 01, 2014

Schrott, ist nach nach ca. 30min Einschaltzeit an 2S verreckt und bis heute nicht ersetzt. Vergesst den den Dreck.

• Overall
• Quality
• Value

Customer Rated

Dec 12, 2013

Have build in KDS600FBL on Swashplate in late Spring 2013. Fly with Microbeast @ 7,4V and TDT Head. Over Summer the Heli has done above 40 Flights Slow 3D. Servo is fast, strong and smove.
By powering up the Heli before Flight, i hear the Nickservo scratch. At home i find the Gear has lost the top of the tooth over the quater round. Fond the same Picture in Rollservo. The Gear is to weak for the Power of this Servo.
Please HK, give these fine Servo a better Gear for 5 or 10 Buks more!

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 11, 2013

They seam to have enough power and speed , not sure how tough they are as I was landing my 50cc the were in and landing gear collapsed , bit of a weak design and when i checked the aileron servos the gears were sticking then i tested to see how they handled some resistance and they sheared the gears quite easily , the elevator and rudder ok but time will tell I guess to see if they last .3 Star just cause Im not sure at the moment and they are not that cheap compared to the 958

• Overall
• Quality
• Value

Certified Buyer Rated

Jan 22, 2013

very good, fast and strong, I like aluminium heat sink. thank you HK

• Overall
• Quality
• Value

Customer Rated

Jan 15, 2013

Testing them on the swash of a X7, with a 47902 on the tail.
Using a servo tester, speed was slower as specs, power ok.
Accuracy fair-good, not as good as some other servos (Futaba, servox) i have used.

These servos seem to be really powerhungry. Some of the erratic behaviour of these MI servos reported elsewhere might be related to that fact. When hooking up just one servo to a std HBEC at 6v, the BEC was sometimes exhausted by just powering up, causing erratic behaviour. With a WR Super BEC or Quasar no problems.

I have noticed a slight tremble, especially on the tail. Running the tail at 250mhz.

• Overall
• Quality
• Value

Customer Rated

Dec 15, 2012

servo resolusion good



servo speed good





but,,,



servo horn > weig down (by hand) -> servo horn (>Vibration(tremble.)),,,maybe Semiconductor chips > Cheap





other expensive servo-> Not vibration(tremble)...

• Overall
• Quality
• Value

Customer Rated

Oct 17, 2012

I am using them on a Flybarless Trex700e cyclic, so far they are excellent. Fast, Accurate and Strong, The casing has been updated since this photo, they now have the same case as PRODUCT ID: 019000001 which is actually bettter.

• Overall
• Quality
• Value

Customer Rated

Feb 22, 2012

Used for elevator on a 6 meter glider during extrem speed . Fantastic answer, do not find any bad thing to say.