Registreren

Product Finder

Instellingen

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Registreren

icanFly EP Trainer 1370mm EPO (PNF)

icanFly EP Trainer 1370mm EPO (PNF)

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Gewicht:
1677 g
SKU:
Icanfly-PNP
Product
Omschrijving

De icanFly heeft alle juiste ingrediënten voor een trainer, het is gemaakt van sterk en makkelijk te EPO schuim te repareren, beschikt over volledige 4-kanaals control, een rubberen band gemonteerd vleugel die stoten zal nemen en heeft een fatsoenlijke spanwijdte waardoor het in staat is een beetje handling wind.

Vanwege het hoge niveau van de fabriek afwerking, met de motor, ESC en servo's al geinstalleerd, de icanFly zal weinig tijd in elkaar te zetten, is er ook lijm en een volledige handleiding inbegrepen. Het model is zeer praktisch met dank aan het is gemakkelijk om vleugel te verwijderen voor het transport en de plug in het onderstel, waarmee u op elk oppervlak vliegen.

Het licht vliegen gewicht van de icanFly betekent dat slechts een klein en goedkoop 1000mAh 2s LiPoly nodig is, het betekent ook dat er voldoende prestaties uit de vooraf geïnstalleerde bell motor, wordt een extra prop ook voor als het onvermijdelijke gebeurt! Voor nieuwe piloten, de icanFly biedt een goedkope, praktische en leuke start in de hobby, voor de meer ervaren piloten, het is gewoon leuk!

specs:
Spanwijdte: 1370mm
Lengte: 917mm
Wing Gebied: 22.8dm2
Flying Gewicht: 600g
Motor: 1300kv Brushless Outrunner
ESC: 18A w / BEC
Servo: 9g x 3
Prop: 9x5 2pc

vereist:
Uw Eigen 4-kanaals TX / RX
1000mAh 2s LiPoly Battery
Geschikte LiPoly Charger

Product
Specifications

Aanvullende Informatie

  • Sku:
    Icanfly-PNP
  • Brand:
    Nee
  • Capaciteit ( mAh )
    Nee
  • Gewicht ( g)
    1677.00
  • Lengte:
    900.00
  • Breedte:
    190.00
  • Hoogte
    310.00
Community
Discussions
Rate&
Review

Schrijf je eigen recensie

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
This is a great beginners plane. I thought myself to fly Rc planes on this model and would recommend it. It is very stable and will fly so slow when needed. The landing gear is weak and is not up to rough landings a beginner is likely to have. It's easy to hand launch and belly landings are a breeze. You will need to reinforce the motor bulkhead after the first nose in.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is one of the best trainers you can get. I used it to practice my landings. You need to make the following changes:

a) Upgrade the motor as someone mentioned below
b) Epoxy the landing gear in the housing and epoxy a piece of balsa over the plastic
c) Tape the area around where the rubber bands sits as it bites into the foam
d) Put wheel retainers

Make sure your ailerons are tightly clamped as there is one servo for both. The ailerons can be a bit weak in the wind.

With this configuration it takes off within a few feet. Great plane and highly recommend for newbs. I have had over 30 flights. It takes a 1800mah 3 cell and the cg is fine with it.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is a great plane for beginners as well as experienced pilots. It easily handles winds upto 10 KM but you must upgrade the motor to AX-2306N which is a direct bolt on as someone else has suggested. Upgrade the ESC to 30 A and you can use a 1600 mah or 2200 mah battery to give 40 minute flights. It can be used as a stable trainer. The aileron is a trade off as one servo is clamped to both the sides but it works fine just make sure the push rods are properly tightened. Replace the rubber bands holding the wings regularly. The landing gear is pretty crap and pops out easily. You will need to reinforce the housing and add a more springy wheel axle with larger wheels. It is very stable in flight and a delight to fly. Perfect for a relaxing on a calm afternoon/ morning.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
The overall impression: a bit flimsy but OK for a cheap foamy. It is a bit disturbing to read on the package that there is a "steerable nose wheel" featured. Wat??
Building was event less as it poses no challenges. Never found out what the transparent plastic bit was for, and there are spare hinges that are not needed. Bend all the control surfaces back and forth before attaching them, cause they are stiff. Or make use of the spare hinges?
Looking at the short and thin CF spar and bending the wings a bit it is obvious that the wings will buckle first time you correct hard in a loop. I applied 2 stripes of 36 mm reinforced tape both on top and bottom of the wings. That gave it some stability. Also, some extra tape where the rubber bands hold the wing for protection. Extra markings on the bottom of the wings will help to recognize orientation in flight.
Before I even flew it I added one 0.8mm washer on the right to the motor mount, to get rid of the exaggerated right thrust, and added 2 washers on the top to give it the down thrust it will need.
The propeller 9x6 is not good quality. On a 2s it produces 260g thrust at 6.3A. On 3s 420 g at 10A, heating up the motor a lot. So I ditched it and replaced it with a GWS 8x4 DD and use 3s batteries. That gives 420g thrust at 8A, which is plenty, and the heat sink stays at 50 deg C . The ESC is cool.
It flies well and forgiving. Goes fast
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
great first plane with a little bit of common sense . the wing spar is a bit small the wing is flimsy easily fixed with longer carbon rod and the motor is very under powered on 2 cell but the system works good on a 3 cell i just cut the v in front of the motor a little bigger for more cooling and no over heating problems at all very easy to finish assembly cg is good there was not enough down thrust on mine so fixed it by adding a washer to top of mount. foam is strong had one crash from 300m up nose first into a tennis court and only broke motor mount which was just a glue fix wing and fuse held up no problems prop didn't even break. great fun to fly and it can fly in a fair bit of wind
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
The spa rod for the wing is way too small so the wing bends like a wet sponge. The wing and tail don't line up. The under carriage is too tight to install, if I push it any harder I think something will break.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I own three for learning to fly overall foam quality is great and foam will take a heck of a beating and still fly great. Motor is way underpowered on 2 cells not sure if 3 cells a viable option so i simply replaced engine with AX-2306N-2000 bolts stright on and a 8 * 3 prop and you will have a safe stable trainer.

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Its the best!! I love this plane. I am a noob to RC flying and this is perfect. HK done great with this plane! 5 Stars!!!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Good quality and easy assembly, two things have notice after flying is: engine torque angle is way too much so added a washer to bring back to parallel, solved the tendency to turn right when power is applied. Huge underpowered with 2cell, no wind using std electrics etc it needed 100pcnt throttle constant. Tried 3 cell, better balance and performance but ESC and Motor red hot after 2 min flight. 2cell = 5/10 and 3cell =10/10 so I will be upgrading
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I learn RC using this plane. Finishing quality is very good, smooth and shining. The foam is super tough. I placed a clear tape all over its fuselage and wing and it survives with almost no damage after several crashes and still fllies strong until today. The whole electronics (servos, ESC, motor) are crap, so discard the whole thing. The motor is too small to spin 9X5 prop and if you use 3S lipo, you will melt the plastic mounting due to overheat. I upgrade mine using KDA 28 size motor 1200KV, use master airscrew 8.5X6 prop, 30A Hobbywing ESC and custom build the mounting using balsa wood and it flies brilliantly with 3S 2200mAH (cg is perfect with this set up). Happy flying everyone
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Productlabels

Gebruik spaties om verschillende labels te scheiden. Gebruik enkele aanhalingstekens (') voor zinnen.