KD36-60-06L 4000kv borstelloze Inrunner (11T)

• Overall
• Quality
• Value

Customer Rated

Jun 12, 2011

Tested today in my hotliner with 4s 6,7:1 & 16x17: 160amp and 40"motor time come down cold 38* celsius

• Overall
• Quality
• Value

Customer Rated

May 01, 2011

I just run this in F5B style.

Used Setup:
Keda 36-60-6L on P32 6.7 Gear
Castle Creations Phoenix 125
GM 17x21 Prop

Pulling 3,4 KW out of it

After 32 Seconds i did 1300w/min :)

• Overall
• Quality
• Value

Customer Rated

Apr 05, 2011

Im running this motor in a Losi SCTE 4x4 short course truck with a 100A hobbyking ESC, 13t pinion 40 spur, turnigy 5000mah 40c and zippy 5000 30c batts.

its got plenty of grunt to move this 7lb truck and does so with ease.

2s is plenty for this motor, with 4s its absolutely INSANE!!!

i would recommend a lower KV motor for other shortcourse racers so you can gear it up if you need speed and not have to worry about temps. after about 10 mins of HARD speeding around, lots of full throttle its temp was about 145*F.

• Overall
• Quality
• Value

Customer Rated

Apr 02, 2011

This motor is pretty much perfect for short course applications, i've used mine with a HK150A esc in sensorless mode in my jammin scrt10, i get a bit of cogging but thats to expect when you run sensorless. I've run through 3 5Ah and 1 5.2Ah 2s lipos in a row and it stayed below 40 degrees Celsius through the whole run, impressive! Power is comparable to Tekin or novaks 550 can motors, even on high traction surfaces like asphalt it spins out of control if i pull the throttle. Fit and finish is really good, they include 3 4mm bullet connectors to solder to your esc. Can't think of anything bad about it, was gonna upgrade to a tekin later but this exceeded all my expectations so i cant see any reason to change it, def 5 stars!

• Overall
• Quality
• Value

Customer Rated

Jan 17, 2011

Perfect motor for Slash 4x4. It fits without modification and without moving the stock speed control. This motor will allow you to keep pace with those high priced SCT 4x4 brushless systems, and because you can keep all of the stock electronics your vehicle remains waterproof for bashing in snow or wet weather. With a 17t pinion on 7.4v my Slash 4x4 reaches over 50mph and has more torque than your tires can handle on any surface. For warmer weather I do recommend a clip on heat sink for the motor as well as a fan for the ESC just to be safe, though I haven't had any issues with overheating. Also make sure to use a battery with at least 30C discharge capacity, otherwise the hihg amp draw of this motor will damage your low C rate pack.

• Overall
• Quality
• Value

Customer Rated

Oct 15, 2010

Just see, my rustler with that motor on 3S 8800mah 25C li-po (the battery was low)

http://www.youtube.com/watch?v=I74fw90HpMM

I use mamba monster ESC.

• Overall
• Quality
• Value

Customer Rated

Sep 29, 2010

Good motor .... very fast ....

run on my Hongnor SCRT10 with ESC HW150 & Turnigy lipo 5200mah 30C (2 cell) with 13 T pinion

• Overall
• Quality
• Value

Customer Rated

Aug 30, 2010

I use this motor on my inferno with a 4s lipo. It pulls wheelstands on command and clocked 100km/h or 65mph. Without a heatsink and fan the motor did get very hot but with a heatsink and fan was ok and i am happy with the performance

• Overall
• Quality
• Value

Customer Rated

Aug 25, 2010

I have run this motor in my 1/8buggy. It has been clocked by a radar gun at 95klm/h & it also smoke the foam tyres on the road when I do burnouts. Very happy with this product.

• Overall
• Quality
• Value

Customer Rated

Aug 24, 2010

I run this motor in my Castor 1/8 buggy, on 4cells. It has been clocked at 92klm/h with a radar gun & it smokes the foam tyres on the road when I do burnouts!! Very happy with product.