New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

Kingduino Fio ATmega328P Microcontroller

Kingduino Fio ATmega328P Microcontroller

Discontinued Product

Please continue searching for a similar product.
SKU:
381000054
WANT FREE SHIPPING? Click here to find out more!

De Arduino Fio is een microcontroller raad van bestuur op basis van de ATmega328P draait op 3.3V en 8 MHz. Het heeft 14 digitale input / output pinnen (waarvan 6 kan worden gebruikt als PWM uitgangen), 8 analoge ingangen, een on-board resonator, een resetknop en gaten voor montagepen headers. Het heeft aansluitingen voor een Lithium Polymer batterij en is voorzien van een lading circuit dan USB. Een XBee socket is beschikbaar op de onderkant van het bord.

De Arduino Fio is bedoeld voor draadloze toepassingen. De gebruiker kan schetsen met een FTDI kabel of breakout board te uploaden. Bovendien, door een aangepaste USB naar adapter XBee zoals XBee Explorer USB, de gebruiker kan schetsen draadloos uploaden. Het bord wordt geleverd zonder voorgemonteerde headers, waardoor het gebruik van verschillende soorten aansluitingen of direct solderen draden.

specs:
Microcontroller: ATmega328P
Operating Voltage: 3.3V
Input Voltage: 3,35 ~ 12V
Input Voltage voor Charge: 3.7 ~ 7V
Digitale I / O Pins: 14 (waarvan 6 voorzien PWM-uitgang)
Analoge ingang Pins: 8
DC stroom per I / O-Pin: 40mA
Flash-geheugen: 32KB (waarvan 2 KB gebruikt door bootloader)
SRAM: 2KB
EEPROM: 1 KB
Kloksnelheid: 8MHz
Afmetingen: 65x28x12mm
Gewicht: 8,2 g

* Let op: Dit is geen originele Arduino merkproduct.

  • Sku 381000054
  • Brand -
  • Capaciteit ( mAh ) -
  • Gewicht 19.0000
  • Lengte 75.00
  • Breedte 30.00
  • Hoogte 45.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

I'm not using this with an xBee but a WiFLY board from Roving Networks which gives you full Wi-Fi connectivity.



The board appears identical to the reference design, soldering of the headers and xBee socket is rather poor but nothing that can't be fixed with an iron.



Lots of sticky flux residue on the board but again cleaned in a minute.



it will charge the 1S LiPo anywhere from 3-6v input and a red LED indicates charging, turning off when finished.



If you wish to program this while the WiFLy is connected you will have to do two things.



1. send the command "set sys trigger 0x20" to the module followed by "save"



2. solder a switch between pin 4 of the xBee socked and 3.3v.



When the switch is closed it will put the module into sleep mode and you can program your arduino freely!



When ready to run again set the switch back to off.



Note: if you intend to use hardware debuging with a dragon or jtag-ice you will not need to remove C3 as you would on a Arduino Uno, just unplug the ftdi from the port.



Phew, that was a rambling diatribe!



TL;DR version

Very good board, very good price, a few soldering issues.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I'm not using this with an xBee but a WiFLY board from Roving Networks which gives you full Wi-Fi connectivity.



The board appears identical to the reference design, soldering of the headers and xBee socket is rather poor but nothing that can't be fixed with an iron.



Lots of sticky flux residue on the board but again cleaned in a minute.



it will charge the 1S LiPo anywhere from 3-6v input and a red LED indicates charging, turning off when finished.



If you wish to program this while the WiFLy is connected you will have to do two things.



1. send the command "set sys trigger 0x20" to the module followed by "save"



2. solder a switch between pin 4 of the xBee socked and 3.3v.



When the switch is closed it will put the module into sleep mode and you can program your arduino freely!



When ready to run again set the switch back to off.



Note: if you intend to use hardware debuging with a dragon or jtag-ice you will not need to remove C3 as you would on a Arduino Uno, just unplug the ftdi from the port.



Phew, that was a rambling diatribe!



TL;DR version

Very good board, very good price, a few soldering issues.

Customer files
Arduino Fio Schematic Download [51]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!