New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

Kingduino Nano V3.0 Microcontroller Board

Kingduino Nano V3.0 Microcontroller Board

Shipped From:
  • USA
Discontinued Product

Please continue searching for a similar product.
SKU:
009000007
WANT FREE SHIPPING? Click here to find out more!

De Arduino Nano is een kleine, volledig en breadboard-vriendelijke board op basis van de ATmega328. Het min of meer dezelfde functionaliteit van de Arduino Duemilanove, maar in een andere verpakking. Het ontbreekt alleen een DC power jack, en werkt met een Mini-B USB-kabel in plaats van een standaard.

De Nano 3.0 heeft een aantal faciliteiten voor het communiceren met een computer, een andere Arduino, of andere microcontrollers. De ATmega328 biedt UART TTL (5V) seriële communicatie, die beschikbaar zijn op de digitale pennen 0 (RX) en 1 (TX) is. Een FTDI FT232RL op het bord kanalen deze seriële communicatie via USB en de FTDI drivers (meegeleverd met de Arduino software) te voorzien van een virtuele COM-poort om software op de computer. De Arduino software bevat een seriële-monitor die het mogelijk maakt eenvoudige tekstuele gegevens van en naar de Arduino boord te worden gestuurd. De RX en TX LEDs op de raad van bestuur zal knipperen wanneer data wordt via de FTDI chip en USB-verbinding met de computer wordt verzonden (maar niet voor seriële communicatie op spelden 0 en 1).


* Opmerking: Dit is geen origineel Arduino merkproduct, wordt geproduceerd met dezelfde componenten en functionaliteit van een andere fabrikant.


specs:
Microcontroller: ATmega328
Operating Voltage (logisch niveau): 5V
Input Voltage (aanbevolen): 7-12V
Input Voltage (limieten): 6-20V
Digitale I / O Pins: 14 (waarvan 6 voorzien PWM-uitgang)
Analoge ingang Pins: 8
DC stroom per I / O-Pin: 40mA
Flash-geheugen: 32KB (ATmega328) waarvan 2 KB gebruikt door bootloader
SRAM: 2KB (ATmega328)
EEPROM: 1 KB (ATmega328)
Klok Snelheid: 16 MHz
Afmetingen: 43 x 18 x 19mm
Gewicht: 6g

  • Sku 009000007
  • Brand -
  • Capaciteit ( mAh ) -
  • Gewicht 17.0000
  • Lengte 118.00
  • Breedte 15.00
  • Hoogte 65.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Seems to have counterfeit FTDI chips. Bought two, began receiving this error after an update:

stk500_getsync(): not in sync: resp=0x00

After a lot of research, I found that downgrading the driver works, and that it is due to a counterfeit FTDI chip on the board. now I see there is a Windows 8 upgrade that may make this impossible.

If it weren't for this, I'd have rated them 5 stars all across the board.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Seems to have counterfeit FTDI chips. Bought two, began receiving this error after an update:

stk500_getsync(): not in sync: resp=0x00

After a lot of research, I found that downgrading the driver works, and that it is due to a counterfeit FTDI chip on the board. now I see there is a Windows 8 upgrade that may make this impossible.

If it weren't for this, I'd have rated them 5 stars all across the board.

Bought just one to trial as I've been a PIC assembler programmer for decades and wanted to check out the Arduino and its IDE. Had some problems, to cut a long story short the Nano A0 pin had a dry joint and would intermittently disconnect from the A0 header-pin and instead it would pick up the voltage from the adjacent A1 pin. Used it successfully by leaving A0 disconnected and using other pins instead. Not a brilliant first impression of Arduinos.
Cheers
Phil

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Bought just one to trial as I've been a PIC assembler programmer for decades and wanted to check out the Arduino and its IDE. Had some problems, to cut a long story short the Nano A0 pin had a dry joint and would intermittently disconnect from the A0 header-pin and instead it would pick up the voltage from the adjacent A1 pin. Used it successfully by leaving A0 disconnected and using other pins instead. Not a brilliant first impression of Arduinos.
Cheers
Phil

I bought one to evaluate. On arrival I found it has an intermittent connection from A0 to the header pin, when it happens to be disconnected it picks up the voltage on A1 instead.
Otherwise functions ok, no problems connecting to Windows 8, but don't think I'll buy any more from here. Phil_G.
www.singlechannel.co.uk

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought one to evaluate. On arrival I found it has an intermittent connection from A0 to the header pin, when it happens to be disconnected it picks up the voltage on A1 instead.
Otherwise functions ok, no problems connecting to Windows 8, but don't think I'll buy any more from here. Phil_G.
www.singlechannel.co.uk

perfeito para pequenos projetos...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

perfeito para pequenos projetos...

Okay - but to expensive. You will get cheaper ones at the www - roundabout 1,30 $ less........

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Okay - but to expensive. You will get cheaper ones at the www - roundabout 1,30 $ less........

I feel sorry to buy this item as I spent one full day to try to upload sample sketch but I failed to at least communicate with it. I advise you not to buy it.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I feel sorry to buy this item as I spent one full day to try to upload sample sketch but I failed to at least communicate with it. I advise you not to buy it.

works very well, I like the small size and the reset button, the price is just right, I have Arduino uno R3 units, but they are a bit big to put on a RC craft, so I use the UNO to write my program and work out the bugs, then send the finished program to the little nano, connect my wires and off we go! if the pins are in the way, I unsolder them and use 90 deg pins so I can mount the nano flat, try to keep it away from the RX, the clock on the nano may cause noise problems for the RX.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

works very well, I like the small size and the reset button, the price is just right, I have Arduino uno R3 units, but they are a bit big to put on a RC craft, so I use the UNO to write my program and work out the bugs, then send the finished program to the little nano, connect my wires and off we go! if the pins are in the way, I unsolder them and use 90 deg pins so I can mount the nano flat, try to keep it away from the RX, the clock on the nano may cause noise problems for the RX.

The nano. Arduino for the s,all hearted

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The nano. Arduino for the s,all hearted

First of all, I am not a huge Arduino fan because I think most boards in the family are overpriced for the performance. The one plus about the Arduino family is the good software library support. Having said that, the main reason I got my 4 Arduino Nanos is because the HK price finally makes it a great value, especially since I can get them from the US warehouse. The quality of these clones is great. Only caveat is that you may have to try re-connecting to USB several times before computer recognizes it, but I believe that's true of genuine Nanos too. I'll have to find a shorter cable and see if that improves things. Once it does connect, you can use the Arduino dev IDE w/o problems.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

First of all, I am not a huge Arduino fan because I think most boards in the family are overpriced for the performance. The one plus about the Arduino family is the good software library support. Having said that, the main reason I got my 4 Arduino Nanos is because the HK price finally makes it a great value, especially since I can get them from the US warehouse. The quality of these clones is great. Only caveat is that you may have to try re-connecting to USB several times before computer recognizes it, but I believe that's true of genuine Nanos too. I'll have to find a shorter cable and see if that improves things. Once it does connect, you can use the Arduino dev IDE w/o problems.

I do not know if it was working before but it is always a good idea to burn the boot loader to Arduino if there are any problems. I am not sure if just a USB connection will burn it because I used an usbasp programming stick instead.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I do not know if it was working before but it is always a good idea to burn the boot loader to Arduino if there are any problems. I am not sure if just a USB connection will burn it because I used an usbasp programming stick instead.

  1. 1
  2. 2
  3. 3
Customer files
579544975X83077X8.pdf Download [854]
ArduinoNanoManual Download [854]
arduino nano 328 layout Download [153]
Xbee Arduino Receiver Sketch Download [7]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save