Hier is een uniek laser gesneden balsa kit voor modelbouwers die genieten van crafting hun modellen op de traditionele manier, genieten van de tijd die nodig is om een model uit kitvorm te bouwen.
Little Bug is een grappige naam, maar het past bij deze cartooneske op zoek vliegende vleugel!
Geleverd als een all balsa / ply laser gesneden kit met in elkaar grijpende componenten zorgen voor een gemakkelijke en nauwkeurige constructie. Als u genieten van de build kunt u genieten van deze kit!
De radio en macht systeem zijn beide zeer eenvoudig, het model vliegt op een 28mm 1200Kv outrunner en maakt gebruik van eenvoudige elevon & roer controls vlucht.
Bouwen iets dat zal onderscheiden van de massa!
Motor: 28mm 1200kv outrunner
Batterij: 3s 1800mAh
Uw eigen 4-kanaals radio - met elevon mengen
3 x 9g servo
28mm 1200kv outrunner
1800-2200 3s Batterij Lipo
Basic schuren gereedschap
Gewicht ( g)
Fantastic little kit, Ordered from EU warehouse to UK in 7 days, went together very well, A beginner might have problems as instructions ain't the best in the world but ok for someone whos use to building kits, Every part is lazer cut including the windscreen. I decided to put the aileron servos under the wing to make it look better & added some hardwood to u/c for strength, Also added some 60mm Piper cub wheels & Decals to mine (see Little Cub photos in files tab). Am using a 40amp esc and spare motor i had in my spares box, Will give it a maiden flight soon.Fantastic little plane kit, Instructions are a bit hit and miss at times but goes together very well, ordered from EU warehouse to UK in 7 days. Built mine into a mini piper cub(see photos tab)bello da vedere, qualche problema nel trovare il giusto cg, facile da costruireExcellent value for money. Easy build. Instructions are not very helpfull but with planning and laying out of pieces you can puzzle it together. The leading edge for the wing was a little underdimensioned. Plane arrived well packaged, and well cut. THX HKWhat a neat plane to build. As usual the plans are not that great, however everything went together really well as the laser cutting was spot on. I have been told it looks like a cartoon plane from Disney. So the smile I put on front of it matches mine.Quality of ply & balsa was excellent. Die cutting was of a high standard and required only minimum effort to remove from sheets.
Wing is of traditional balsa construction, mainly used a white glue for assembly.
Basic fuselage is ply, all parts interlocked easily and required minimum gluing (dry assembled then glued with cyno).
Only negative is the instructions, not easy to identify the individual parts, used the pictures for a guide and my own experience.
Not recommended for a novice builder.
Overall it is a top kit to build during the cold weather.
Excellent value for money
Great kit. went together as expected. This is only my second attempt at building a laser cut kit the first being the HK GeeBee. I really enjoyed this build. I modified the bottom of the fuse to make a battery compartment hatch using the knock outs. The C of G as shown on the "instruction sheet" is COMPLETELY WRONG! and caused a laundry incident on the maiden flight. The correct position is approx. 25-30mm from the leading edge. This put the battery pretty much as far forward as it would go. Strap the front wheel axle to the bottom of the fuse NOT through holes in the fuse sides if you do a hard landing it will damage the fuse sides. Put them as far forward as you can to find substantial wood. I actually "beefed up" where the screws would go so that they had plenty of "bite". I used approx. 60pcnt throws on the ailerons and 45pcnt on the elevator-not critical if C of G correct. Rudder..whatever! I didn't attempt to make the tail wheel steerable as the rudder id to thin but if you were to modify it you could.Wanted to build a model the old fashioned way, and I found the right model for it. The construction is a bit weak at some points especially the wing attachment to the body. But some extra balsa pieces got it pretty solid. And the body structure is a bit crocked, but pin the whole structure down to the buldingbord as you glue it sorted that problem out. The blueprints are a bit hard to understand so its not for beginners. And it is a bit hard to fly also, you need to use all your rudder to turn it and its a bit tail-heavy even whit 3S 2450mah all the way to the front. 2830 1200kv is a bit underpowered. Take off is real fun to watch. It runs fast like a formula 1 car because the wing is not angeled towards the air. But it looks real funny in the air and my girlfriend Thinks its real cute.Nice little plane, but Building and flying this plane is not for the beginer.
Video from maiden
http://youtu.be/FM2LeUW2xegI really enjoyed this little bug , it went together easy and with no fuss although previous building experience would be an advantage. I built a cowl out of balsa as the bug looked unfinished . it flies well cg needs to be 55mm -60mm
Colourful little bug download now [97kb] No File Name download now [84kb] Lil bug red and yellow download now [1760kb] Yellow and red download now [1760kb] Firebug3 download now [110kb] Firebug1 download now [201kb] Firebug2 download now [140kb] No File Name download now [949kb] No File Name download now [45kb] No File Name download now [53kb] No File Name download now [37kb] No File Name download now [49kb] Photo Little Bug TheBus download now [984kb] Little Bug Sweden 1 download now [191kb] Little Bug Sweden 2 download now [221kb] Crazy Bug download now [1023kb] Crazy Bug download now [1005kb] Construction (en franÃ§ais) download now [7071kb] No File Name download now [164kb] Little Cub (Dumpy) download now [878kb] Little Cub (Dumpy) download now [878kb] IMG_0970.JPG download now [4.23Mb] IMG_0970.JPG download now [4.23Mb] IMG_0977.jpg download now [4.37Mb] IMG_0977.JPG download now [4.25Mb]