Leverancier worden Blog Nieuwe items
Registreren

Totale prijs

€ 0,00

Winkelmand 0 Winkelmand 0 Loading...

Metal Tail Assembly Compleet HK-450TT PRO FBL / Trex 450PRO (torque tube versie)

Generating Links

Metal Tail Assembly Compleet HK-450TT PRO FBL / Trex 450PRO (torque tube versie)

Prijs:

Now save bespaar € 0,00 € 0,00

€ 17,40
Al gekocht Discontinued Product

Please continue searching for a similar product.
SKU:
155000100
Geen verzendkosten? Klik hier meer leren!

Dit is de volledige metalen staart assemblage voor de HK-450TT PRO FBL en Trex 450PRO helikopter kit (torque tube versie). Het beschikt over een verbeterde metalen staart slider en de staart schuifregelaar arm. Dit geheel is gemaakt om zeer nauwe toleranties en heeft geen slop verschaffen locked-in tail prestaties.

Upload video

Registreer u om video's te uploaden aanmelden of registreren

Onderwerpen
Sorteer op
Meest recente onderwerpen
* Bijnaam:

* Uw antwoord:


Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
annuleer
Bevestig
Plaats een nieuw onderwerp
* Bijnaam:

* Uw onderwerp:



Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
Onderwerp plaatsen

Registreer u om beoordelingen te schrijven aanmelden of registreren

JamieF | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

May 10, 2013

The product doesn't work. The tail pitch slider is far too wide over the tail shaft = movement in the blades and jamming of the pitch slider as it slides across the tail shaft.

Hobbyking admit that this is a common complaint but they say that it was designed that way. Therefore, no fault and refuse to rectify the issue.

Waste of money.

JamieF | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

May 01, 2013

cheap, but it's not worth a penny!
The slider arms lock against the metal control arm underneath on full pitch = catastrophic failure.
Poor machining. There has been no care or attention in machining this part. Rough edges, drill holes off centre. The bearing isn't line-up properly so the gear sits to one side.

Definitely worth paying double price for genuine align parts.

| Geverifieerde koper

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Apr 04, 2013

sin probar pero parece bueno

turismo05 | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

Oct 01, 2012

Very dissapointed in this, the tail slider is not smooth, there is a fair bit of slop in the arm at the ball joint ( very loose fit ). Torque tube drive dont centre. Very poor Quality.

Hoovernaut | Geverifieerde koper

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Sep 14, 2012

Very nice quality. Every scew was locked. The slop is minimal, better than the old version from the Pro which I had.

John | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

Aug 31, 2012

I've had a lot of problems with tail slop on my HK450TTpro. I bought two of these, because they looked close to the improved Align tail and they cost a lot less.

However, the first one broke during maiden flight test hovering. The heli suddenly started spinning. The pitch control slider broke, rendering the whole assembly inoperative.

I was glad I had two, because the second one got me back in the air. But I have ordered the more expensive Align part, and I am considering never purchasing HK parts again.

denny | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

Aug 18, 2012

very little slop,not zero, but very good, nice
very little slop,not zero, but very good, nice
very little slop,not zero, but very good, nice

fishfiend | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

Aug 03, 2012

I had to review this tail assembly,because I bought it to replace a troublesome tail unit on my second 450pro clone. This particular clone flew perfectly until I crashed it, and since then I just couldn't get the tail to run nicely, replaced bearings, etc.. finally gave up, and ordered this one to see if it would be any better.
Got it today, unfortunately it was missing that little metal pin that goes in the hole of the tail boom to lock it in, fortunately I had an older busted up one that I robbed one off. I've had many clone tail unit, and almost all of them need adjustments to stop them binding, whether its loosening a screw, or removing crusted lockite. With this assembly I held the tail,and wiggled the control arm...very little slop,not zero, but very good, nice and loose too. I flipped the grips, and checked for lockite, all ok.

Once fitted,I adjusted the limits on my cx3100 and popped it into idle up..lovely! A nice crisp tail response, no wag and no bounce,just how it should be..My other clone flys nearly as well,and when it next takes a dive I shallbegetting another of these to replace the tail..I just wish they had a standard 450pro tail,not the aluminium block and silly metal pin thats a pain to remove..oh well!

Upload bestand

Registreer om bestanden te uploaden.
Alstublieft aanmelden of registreren om nu hobbyisten te helpen!