New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

MultiWii SE V2.0 Flight Controller w / FTDI

MultiWii SE V2.0 Flight Controller w / FTDI

Discontinued Product

Please continue searching for a similar product.
SKU:
381000133
WANT FREE SHIPPING? Click here to find out more!

De MultiWii SE V2.0 is een gyroscoop / accelerometer op basis vlucht controller die is geladen met functies. Met uitbreidingsmogelijkheden en volledige programmeerbaarheid, kan dit apparaat te bedienen zowat elk type vliegtuig. Dit is de ideale vlucht controller voor uw multi-rotor vliegtuigen.

Kenmerken:
• Klein formaat, 35x35mm montagegaten
• 6 ingangen voor standaard ontvanger en PPM SUM-ontvanger
• Tot 8-as motorvermogen
• 2 servo-uitgang voor PITCH en ROLL cardansysteem
• Kan gebruik maken van de uitgang van een servo's om een ​​camera knop te activeren
• FTDI / UART TTL aansluiting voor debug, uploaden firmware of LCD-scherm
• I2C aansluiting voor verlengen sensor, I2C LCD / OLED-display of Crius I2c-GPS NAV board
• Aparte 3,3V en 5V LDO voltage regulator
• ATMega 328P Microcontroller
• MPU6050 6 assige gyro / accelerometer met Unit Motion Processing
• HMC5883L 3-assige digitale magnetometer
• BMP085 digitale druksensor
• Aan boord logisch niveau converter

Vliegtuigmodus:
• Een van de volgende fundamentele modus
- Acro
- Niveau
- Alt Hold
- Head Lock
• Optionele modus
- HeadFree (CareFree)
- GPS-Hold (Need GPS-ontvanger + I2C-GPS NAV Board)
- GPS Keer terug naar de beginstand (Need GPS-ontvanger + I2C-GPS NAV Board)

specs:
Afmetingen: 40x12x40mm
Gewicht: 9.6g
Fixing hole spacing: 35mm (Het kan worden veranderd om 45mm door Crius Distribution Board)
Hole diameter: 3mm

Pakketinhoud:
MultiWii SE FC x 1
USB programmaraad x 1 (Mini USB-kabel vereist, maar wordt afzonderlijk verkocht)
3pin naar 1Pinx3 kabel 100mm x 2
3pin naar 3Pin kabel 100mm x 1


Meer informatie is te vinden op de website MultiWii.
http://www.multiwii.com

  • Sku 381000133
  • Brand -
  • Capaciteit ( mAh ) -
  • Gewicht 30.0000
  • Lengte 130.00
  • Breedte 10.00
  • Hoogte 90.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Never Buy it from them. they will send you

XZN MWC MultiWii SE Standard multi-Copter 4-axis Main flight con

http://www.geeetech.com/xzn-mwc-multiwii-se-standard-multicopter-4axis-main-flight-con-p-552.html

this board which is very poor and cheaper(US 19) than the item shows in their listing.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Never Buy it from them. they will send you

XZN MWC MultiWii SE Standard multi-Copter 4-axis Main flight con

http://www.geeetech.com/xzn-mwc-multiwii-se-standard-multicopter-4axis-main-flight-con-p-552.html

this board which is very poor and cheaper(US 19) than the item shows in their listing.

They sent me the wrong board the 1st time. Did a RMA to replace wrong board and they sent me the same wrong board again. Can't comment on functionality because I've never received what I ordered!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

They sent me the wrong board the 1st time. Did a RMA to replace wrong board and they sent me the same wrong board again. Can't comment on functionality because I've never received what I ordered!

Good board for my 20 cm. arm small tricopter flying great with D2822/17 kv 1100 motor and 1,5 Ah lipo pack for about 10 minutes of very fun.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good board for my 20 cm. arm small tricopter flying great with D2822/17 kv 1100 motor and 1,5 Ah lipo pack for about 10 minutes of very fun.

Hi All! I've got MultiWii 2.0 installed and running on my Quadro. HobbiKing Rx, HobbiKing 10A ESCs are used. Previously I used HobbyKing Multi-Rotor Control Board and it flied well. On this MultiWii control motors running not fast enough to take quadro off the ground. Even if I move throttle stick to the most up position it does not fly. Can anyone say what is wrong?

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Hi All! I've got MultiWii 2.0 installed and running on my Quadro. HobbiKing Rx, HobbiKing 10A ESCs are used. Previously I used HobbyKing Multi-Rotor Control Board and it flied well. On this MultiWii control motors running not fast enough to take quadro off the ground. Even if I move throttle stick to the most up position it does not fly. Can anyone say what is wrong?

Nice board flying very well But when I tried to plug the battery monitor on A3 input as shown on file "pin assignments" (lipo directly on this input) I burn the Atmega ...I had to add the divider resistor before input the direct lipo voltage.So be carefull bfore wiring this batterie monitor input (A3 pin).
I put a updated picture of the pin assignments with the rsistors in the file section

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nice board flying very well But when I tried to plug the battery monitor on A3 input as shown on file "pin assignments" (lipo directly on this input) I burn the Atmega ...I had to add the divider resistor before input the direct lipo voltage.So be carefull bfore wiring this batterie monitor input (A3 pin).
I put a updated picture of the pin assignments with the rsistors in the file section

I use this board on a 55cm quad, replacing a homemade combo of Arduino ProMini and 4 single sensors boards... Adding a LZ-GPS was very easy because I2C is brought out on its own pin header. The HK S2 V2 board has the Crius V2 layout and comes with preloaded MultiWii 2.1 firmware for Quad X constellation. Firmware can easily be updated or changed to any other config with the FTDI header and Arduino 1.01 software. The MPU 6050 gyro/acc gives really great and stable flight behaviour with an very smooth ACC level mode never seen before. BMP baro is not state of the art anymore (low resolution), but its OK to get a height hold mode within 2-3 meters. Overall: Great board with good quality, small boards size, totally worth the money. Will buy a 2nd one for my Flydumini as soon as they are on stock again.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I use this board on a 55cm quad, replacing a homemade combo of Arduino ProMini and 4 single sensors boards... Adding a LZ-GPS was very easy because I2C is brought out on its own pin header. The HK S2 V2 board has the Crius V2 layout and comes with preloaded MultiWii 2.1 firmware for Quad X constellation. Firmware can easily be updated or changed to any other config with the FTDI header and Arduino 1.01 software. The MPU 6050 gyro/acc gives really great and stable flight behaviour with an very smooth ACC level mode never seen before. BMP baro is not state of the art anymore (low resolution), but its OK to get a height hold mode within 2-3 meters. Overall: Great board with good quality, small boards size, totally worth the money. Will buy a 2nd one for my Flydumini as soon as they are on stock again.

A good product!!! This comes pre-programmed. But the PID values are all out of boundaries. So you will face a hard time setting it up...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

A good product!!! This comes pre-programmed. But the PID values are all out of boundaries. So you will face a hard time setting it up...

bu gne kadar kullandm kartlar arasnda en iyisi.
gps modl de almanz tavsiye ederim.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

bu gne kadar kullandm kartlar arasnda en iyisi.
gps modl de almanz tavsiye ederim.

The ever expandable MultiWii controller

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The ever expandable MultiWii controller

The 0.03 hectopascal maximum resolution of the BMP085 is an optimum enabling the sensor to respond to differences in altitude of 25 cm.



At this days pressure sensors have ~ 10cm. altitude sensitivity!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The 0.03 hectopascal maximum resolution of the BMP085 is an optimum enabling the sensor to respond to differences in altitude of 25 cm.



At this days pressure sensors have ~ 10cm. altitude sensitivity!

  1. 1
  2. 2
Customer files
pin assignments Download [184]
No File Name Download [184]
Newbies Guide (By ATXHELI rev. 04/22/201 Download [452]
pin assignments with Batt monitor resist Download [199]
Flight-Ctrl ME 2.0 Schematic Download [781]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!