Leverancier worden Blog Nieuwe items
Registreren

Totale prijs

€ 0,00

Winkelmand 0 Winkelmand 0 Loading...

Print-Rite DIY 3D-printer - Heat Table (200 x 200mm)

Generating Links

Print-Rite DIY 3D-printer - Heat Table (200 x 200mm)

Prijs:

Now save bespaar € 0,00 € 0,00

€ 47,56
Al gekocht Discontinued Product

Please continue searching for a similar product.
SKU:
629000059-0
Geen verzendkosten? Klik hier meer leren!

Print-Rite DIY 3D-printer - Heat Table (200 x 200mm)

Deze Verwarmde Table (of bed) is een must voor uw bestaande Print-Rite DIY 3D-printer als het helpt om de kwaliteit van uw drukwerk te verbeteren bij het gebruik van ABS, PC, en andere hoge temp filamenten. Het is gemakkelijk te monteren en past direct in het bed drukken.

specs:
Maat: 219 x 219 x 1.6mm
GW: 0,85 kg

inbegrepen:
1 x Controller
1 x Heat bed
1 x ABS glas
4 x Silica films
2 x Clips

Upload video

Registreer u om video's te uploaden aanmelden of registreren

Onderwerpen
Sorteer op
Meest recente onderwerpen
* Bijnaam:

* Uw antwoord:


Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
annuleer
Bevestig
Plaats een nieuw onderwerp
* Bijnaam:

* Uw onderwerp:



Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
Onderwerp plaatsen

Registreer u om beoordelingen te schrijven aanmelden of registreren

Ty | Geverifieerde koper

  • Overall
  • Quality
  • Value

Looks like it will do the job

Jan 12, 2017

This heated bed comes with no instructions at all but its pretty straight forward with out instructions. I havent tried this yet as I need to wire it up to my power supply but I'll revise this when I get some time on it.
I suggest wiring in a toggle switch or some sort of on/off switch that is near the temperature controller so you have something to shut it off quick if need be.
It would be nice if the binder clips that are included were smaller, they take up a lot of room, I'll replace mine with smaller ones.
It also would be nice if a larger power supply came with it, or maybe have the option for one.
Again, I'll revise this once I have some use on this.

Tyler | Geverifieerde koper

  • Overall
  • Quality
  • Value

Incomplete, no instructions.

Dec 22, 2016

Im sure this thing would work great if there any instructions or if it included all the necessary parts to install it. Irritated.

Romeo | Geverifieerde koper

  • Overall
  • Quality
  • Value

Nice

Dec 04, 2016

The bad is nice,works well, but the glass is more larger than screw hole and need to be cut on the corner. The edge is curved and for the price is a good product.

Todd | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

Oct 24, 2016

Update on this heater bed:
The heater bed wasn't heating up all the time. I ended up removing the connector to the heater and checking the continuity of the wires going to the plug and found that the thin power wire to the plug was not fitted correctly and wasn't making contact.
So check the continuity of all wires to the plug from the controller board when you get your heater bed.

Todd | Geverifieerde koper

  • Overall
  • Quality
  • Value

Customer Rated

Aug 21, 2016

Heater bed draws a maximum of 63 watts on my tests and can only be heated to a maximum of about 110c.
The duration of the heating will not last for the duration of long printouts. The time is not known yet, but will update later.
I've got a 250 watt power supply powering both the heater bed and the printer without any problems, so far.

Klantbestanden
Print-Rite manual (Dutch) Download [717]
CoLiDo-Heated-Bed-Installation.pdf Download [303]
Upload bestand

Registreer om bestanden te uploaden.
Alstublieft aanmelden of registreren om nu hobbyisten te helpen!