Hier is een andere grote betaalbare kleine balsa Kit voor de traditionele R / C hobbyist en bouwer die geniet van het construeren modellen uit kitvorm.
The Red Swan is een alles opgebouwd, 4-kanaals, elektrisch aangedreven park vlieg zweefvliegtuig. Het beschikt over scherpe nauwkeurige laser gesneden onderdelen die eenvoudig in elkaar sleuf met weinig gedoe en de vleugel ziet er fantastisch uit wanneer bekleed met doorzichtige afdekking om te laten zien van de constructie.
De kracht systeem kan een eenvoudige kleine outrunner en 2s batterij, met behulp van micro servo's om haar mooie en het licht te houden.
Het resulterende model is een geweldig klein park elektrische zweefvliegtuig die goed presteert, heeft rolroer / lift / roer / motorische controle, maar is sterk genoeg om omgaan met de oneven fly 'Oeps!' ogenblik van beginner flyers en compact genoeg gemakkelijk worden vervoerd.
4-kanaals radio-systeem en 4 x micro servo's
1550kv 15amp Outrunner
batterij 2 of 3s 1300mAh Lipo
Propeller (8 x 4)
Basic hobby gereedschappen (mes, schuurpapier etc.)
Build handleiding vermeld onder het tabblad 'Files' hieronder
Gewicht ( g)
Nice little kit for the money. need a bit of experience to build it. instructions a little bare to say the least!fantastico, ne ho presi 2 a magazzino e uno sempre con me, 1400k lipo 1500-1600 prop 9*4This kit is THE kit for those who love the old school balsa kit..
Wood is good in general and laser-cut parts saves valuable time.
That said, this is not for beginners, the building notes are nonexistent and it is necessary to go on the net to find build logs, fortunately quite numerous.
I just have two disappointments, after assembling and flying with the Red Swan:
First, it is quite heavy. Ready to fly weighed approx 700gr.
For a wingspan of 1224mm he had to fly fast enough to generate the necessary lift.
Then, the weak point is the horizontal stabilizer. It is very close to the ground and the landing must be perfectly horizontal on a very flat surface. The slightest clod of dirt or grass can easily pull the horizontal stabilizer off.
This happened to me twice. The first time the tail has been torn, I rebuilt the entire tail section in plain balsa, much stronger.
Alas, he clung to a clump of grass and the section of the fuselage near the tail (with holes for pushrods) broke ... :(
That said, it's a nice old school kit for a handyman with experience and a good flat ground for landing.
I posted 3 pictures of my Red Swan ( The under files section Cardinal ) just before the maiden flightNIcely cut kit. A lot of fun to build, and they look great when complete. I wish hobbyking would stock more laser cut kits.Fine construction, precise laser-cut parts, but wrong building instructions:
First, the 2 fuselage sides must be prepared with strengthening sticks first, then glued together with bulkhead parts, servo tray and motor mount in one step to avoid distortion!
Second, the order of wing ribs is wrong in the picture as well as in text part 2.02. Correct is 6 pc. B3 in the middle, then on each side one pc. B4, 5 pc. B5, each parted by a pair of B7 glued at both sides of the balsa spars, finished by one pc. B6. The construction should be done on a board using needles to fix the parts, thus obtaining a straight wing.Fine parts, fitting well, but:
Wrong instruction manual!
The two sides of the fuselage must be built symmetrically without yet glueing the bulkhead parts, the motor mount and the servo base. Only when finished, both sides and the mentioned parts must be fitted together in one glueing step.
Otherwise the fuselage will turn out rather distorted!
Second mistake: the denotation of the wing ribs in the picture of the middle wing part and in textpassage 2.02 is wrong. As there are only 2 ribs B4, but 12 pc. B5 and 4 pc. B6, the correct order must be:
6 (or 8? There are 8 pc.!) ribs B3 in the middle, then, spaced by B7, one rib B4, followed by 5 pc. B5 on each side, each spaced by one B7 part, and one B6 rib to strengthen the edges.
The other two B6 should strengthen the edges of the outer wing parts.Soft package, no cover film, no plans.I missed drawing, so I draw him, I upload to files.
Servos will use HXT500.
Motor temporarily 24 grams hexTronik Brushless Outrunner 1300kv.First flight today with a 2822/17 3s and 8*4 prop. Good 3 axes glider slow rolls, loops, inverted flight. Can be used by a beginner (but foamies will be much more crash rsistant...). The manual is really not here to help and 9 gr servos are too big for the ailerons. I have also replace the supplied leading ege of the wing by a carbon fiber tube 3mm. Despite the inexisting and wrong manual, we had good time with my son building this kit and at the end.... Good surprise....great flying capacities!So much potential ruined by horrible plans. I'm about 2/3 done and am looking forward to flying it. Search for my build thread on RC Groups . Com for build information. It's been a fun build so far (other than the lack of instructions). Wood quality is decent but heavy, packing is good, and fit of the laser cut parts is ok.