Niet de snelste vliegtuig op het veld, maar zeker een van de betere kijken en mooi gedetailleerd degenen.Deze kleine Franse ontworpen vliegtuig werd gebouwd licht en wendbaar te zijn. Zo ook is de R / C model versie. Alleen de geringste toename van de macht zal dit een raket in de lucht te maken. Probeer een TowerPro 2408 outrunner naar goedkope nog thrilling prestatie!
Spec.Wing Span: 1045mmLengte: 784mmFlying Gewicht: 630 gWing Load: 35g / dm2Vereist.
Uw eigen TX & RX1800mAh 2S Lipo (7.4V)Servo: 3x9gMotor: Krachtige Brushless Outrunner 2822kvESC: 20A* Servo, motor, esc getoond in afbeelding niet inbegrepen. Voor Plug-n-Fly versie, zie de andere lijst voor hetzelfde model.
Gewicht ( g)
Very beatiful aircraft. Until now is not done to fly. But i can see that is a nice place with a very good value.
I will use it with a emax 2822, Esc tower pro 40A, 3 Micro servos 9g and 1300mha nanotec 3s.
Is easy to buy the eletronics for this great plane. My aircraft doesnt came with the painel. :(Not amazed,but not dissapointed either.The model comes in a nice shiny box and with an egg-style packaging inside.One of the elerons was bumped into while it was packaged,the box should have been bigger.The cowl is very flimsy,i suspect it will break off at the first crash.The servo mounts are quite too far towards the tail,it is difficult to mount the servos.The wing is solid,the landing gear wheels are complete waste,not even centered.The engine mount is very weak,you can bend it by hand very easily.Lots of screws included,that`s nice.The rudder doesn`t quite fit it without adjustments but stays on pretty well.The included adhesive is good,like rubber glue but still dries quick and hold good.Don`t like the nose wheel linkage,no tubing to suport the wire.Tail control lines were too long,have to cut them to lenght.Battery tray is kind of small,nose could be longer.Will post more info after first flight.Going to equip it with 2 HKSCM9 9g servo for elevator and ailerons,for rudder a metalic servo to withstand the steerable nose gear,a DST 1200 kv motor and a 20a esc with 1500 lipoOrdered it 4 days ago and still hasn`t shipped.Will post more info when i received it.Still,best price i`ve found.Will equip it with HKSCM-9 for elevator&ailerons,going for a metal 9g servo for rudder,20a esc, turnigy DST 1200 and a turnigy 3s 1500mah lipo.Great airplane!!!
very nice characteristics of flight and landing too.
Is aerobatic is trainer is awesome this plane
lipo 1300mAh 3s - 2822 1200kv motor - Apc 9x6e propeller - Hk 25-30A Esc
Advice: Put carbon fiber rod across the wing. Strenghten the hinges with tape on the rudder and elevator.
Enjoy!The price is unbeatable.i have been flying this for a long time now and have to report that there have been absolutely no problems with the aircraft.
it will do all of the normal stunts, loops, rolls, stall turns and inverted.
handles strong breezes ok, though landings can be fun.
in calm wind it glides well and touches down gently.
very happy with it as a fun machine, i keep mine fully rigged all the time as it just pops in the boot of the car at a moments notice.Very good and beautiful kit. Was build in 3 hours. Servos, controller and motor 2822 was received in the same box. Thanks to HK.???? ????? ?? ??? ? ?? ????.2nd plane for me...
first is higwing trainer ( Wing daragon 4ch )
first, I use emax BL 2822 1200kv, 20A ESC, 3x9gr Servo, SF 8060 prop.11.1 v 1300 mah 20C Lipo
flying nice looking, smooth and easy landing landing for me.
Now I replace the BL with 2836 1100kv, the other elektronics is same than before
More Power Full, Speed, Glide, more aerobatics is easy ( loops, Roll, Invert )
climb verticall too fast...
will order more for my club
one issue for this, nose landing gear is not so strong