Registreren

Product Finder

Instellingen

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Registreren
Shipped From:
  • Global
  • USA

TowerPro n20 Acro Brushless Speed ​​Controller

TowerPro n20 Acro Brushless Speed ​​Controller

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Gewicht:
30 g
SKU:
TP_N20-Acro
Product
Omschrijving

Amp cijfer: 20A (max 22A burst)
FET's: 12
BEC Current: 1.5A
Timing: Auto (Programmable)
Freq: 8 kHz (Programmable)
Lipo: 2 ~ 3 (Programmable)
NiMH: 6 ~ 16 (Programmable)
Gewicht: 19.5g (22 met draden)
Een deel van de nieuwe reeks van BESCs door TowerPro die nu worden geprogrammeerd met de Programming Box.
Deze BESCs hebben een veel groter scala aan functies en mogelijkheden dan hun voorgangers.
https://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=5448

Manual: http://hobbycity.com/cs/files/

Product
Specifications

Aanvullende Informatie

  • Sku:
    TP_N20-Acro
  • Brand:
    Nvt
  • Gewicht ( g)
    30.00
  • Lengte
    0.00
  • Breedte:
    0.00
  • Hoogte:
    0.00
Community
Discussions
Rate&
Review

Schrijf je eigen recensie

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Esc perfeito para ser usado com o 2822
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very good ESC, but there is no programming possibility as programming cards are not on sale
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
One problem with this ESC - regardless of the setting it has a starting problem with FC 28-05 Brushless Outrunner 2840Kv. The starting is not reliable (a lot of high pitch squeaking and sputtering for 2-3 seconds) and the motor starts average 1 of 3 times. The same motor starts smooth with TURNIGY Plush 25amp Speed Controller. I'm switching over to TURNIGY ESC, as I never had a single problem with any of 5 of them that I have.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very good and cheap spead controller. But be carefull - you can't set anything without Towerpro N20 and L40 Programming Box! I use it with Turnigy 2213 motor at about 17 A current.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I've been running this ESC for over 2 months now in A-10 EDF (twin) with B2435-4040 (I received it instead of ordered HXT2435-4040). Both ESC keep the same rpm through entire throttle range (what is important on twin). The startup is strange (like I wrote before) but it is actually cool.



ESC needs no more than 1ms pulse with to arm. Then it needs fast throttle advance to start (to about 1.2ms or more). At the startup procedure motor revs a little and then slows down. It is like starting a car. After startup if throttle goes below 1.2ms motor will stop and ESC will not start it any more until it is "rearmed" again (pulse width must be no more than 1ms).



In my A-10 I programmed "idle down" (Futaba 8US) as a motor cut-off switch. When the throttle stick is at low position and idle is down the radio transmits 1ms pulse that will arm both ESC. Then I flip the "idle up" switch and this increases the pulse to about 1.2ms At the flip of that switch both motors start, rev up a little and than stay at idle speed. The plane is ready to taxi and flying. During the flight if I move the throttle stick to the lowest position both motors are still running at idle. After landing I flip the "idle down" switch again and motors will stop.

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Die Programmierung mit der Programming-Card funktioniert nicht immer einwandfrei!

Es ist mir nicht gelungen per Programmierung die Drehrichtung zu verndern.

Die Wrmeentwicklung selbst im Ruhezustand ohne angeschlossene Servos ist gewaltig.

Gute Khlung ist ein MUSS.

Verwende ihn bis max 12A.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
These ESCs get warmer to touch than other ESCs that I am using. With the motor off this uses 0.15A while the other 3 brands of ESCs that I tested run between 0.03A and 0.05A. That extra amperage is showing up as heat and will wear your battery down 3x faster if the plane is sitting with the battery plugged in. When at full throttle the amperage draw is the same.



Don't buy it without the programmer.



I'm not disappointed that I bought several of the n20 ESCs....they do work well and are a great price. The programmer is easy to use. So far I haven't had any performance problems or failures.



The battery wires are a little short and the receiver plug wire is a heavy gauge and twice as long as I would like. I've seen this on other Towerpro ESCs too.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Great speed control for a low price. Is virtually the same performance as ESC's that cost 3x this price.

Is perfect for park flyers using 18 or 20 amps like GWS foamies.

I have 4 of them in planes I fly often and they work great.

The programming box gives lots of options.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Been using a pair of these on outrunners on my swamp buugy air boat.

Loads of power - ESc runns cool.

No problems
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I think its best value here in hobbycity. For commnom use there is nothing better. I have 12 pieces and no one defective or some problems. Off course programmer box is needed.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Productlabels

Gebruik spaties om verschillende labels te scheiden. Gebruik enkele aanhalingstekens (') voor zinnen.