Totale prijs

€ 0,00

Winkelmand 0 Winkelmand 0 Loading...

Turnigy 2815 EDF Outrunner 3500KV voor 55 / 64mm

Generating Links

Turnigy 2815 EDF Outrunner 3500KV voor 55 / 64mm

Prijs:

Now save bespaar € 0,00 € 0,00

€ 11,93
Al gekocht Discontinued Product

Please continue searching for a similar product.
SKU:
T28151C3500
Geen verzendkosten? Klik hier meer leren!
Turnigy 2815 EDF Outrunner 3500KV voor 55 / 64mm
specs:
kV 3500
Afmetingen: 51 x 28mm
Shaft: 2.3 / 3.0mm
Voltage: 11.1V
Gewicht: 74g
No-load stroom: 1.9A
No-load RPM: 38.460
Laad stroom: 17.8A
Load RPM: 32.780
Thrust: 485 g
Montagegaten Bolt Circle: 18mm
Mtg. Hole Number & Grootte: 4 x M2.5
 
Inclusief 2 assen, 2.3 & 3.0mm
  • Kv ( tpm / v ) 3500.00
  • Max Currents (A ) 1.96
  • Resistance ( mh ) 36.00
  • Max Voltage ( V ) 12.00
  • Vermogen ( W) 19.60
  • Shaft A ( mm ) 3.00
  • Lengte B ( mm ) 48.00
  • Can Diameter C ( mm ) 28.00
  • Kan Lengte D ( mm ) 17.00
  • Totale lengte E ( mm ) 64.00
attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Upload video

Registreer u om video's te uploaden aanmelden of registreren

Onderwerpen
Sorteer op
Meest recente onderwerpen
* Bijnaam:

* Uw antwoord:


Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
annuleer
Bevestig
Plaats een nieuw onderwerp
* Bijnaam:

* Uw onderwerp:



Voer de tekst in de afbeelding in het onderstaande veld in
*Verificatie code:
Onderwerp plaatsen

Registreer u om beoordelingen te schrijven aanmelden of registreren

SirBiggles | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

Apr 19, 2012

I have a put a post in the forum with stats for this motor a few of its brothers and sisters but ill put them here too. Motor is good quality and I think will run on 4S fine if kept under 500W.

3S 64mm 5 Blade Fan 19A, 220W, 11.7v 450g thrust (in plane)

4S 64mm 5 Blade Fan 30A, 450W, 11.7v 640g thrust (in plane)



3S 64mm 6 Blade Fan 19A, 216W, 11.45v 480g thrust (in plane)

4S 64mm 6 Blade Fan 29.5A, 430W, 14.8v 640g thrust (in plane)

Klant | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

Jun 10, 2010

I bought 2 of these for a GWS-262. I use 2 25A tower pro ESCs and a turnigy 2200mah lipo. Its too much for the lipo, it gets hot and puffed out. I'll try a 2600 mah next. Great motors, lots of power. Great value.

Klant | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

May 28, 2010

Looks are good, some flaws.

I had to rebalance both of my motors, I needed lots of CA to balance them but after balancing they ran fine.



Axles supplied with motors were 2.3mm , 3mm and 3.3mm , but 3.3 mm will not fit because the hole is already almost too tight for 3mm axle!

I had to use brute force and hammer to get 3mm axle of and install 2.3mm.



Real life performance will tell more.

khess | Geverifieerde koper

  • Quality
  • Value
  • Overall

Customer Rated

May 08, 2010

Motor appears to be of good quality. On a GWS 64mm, 6-blade fan, Hyperion 3S 2500mAh 25C, Phoenix 25A ESC-low timing, I was pulling 22 amps and 239 watts at 11 volts WOT. Sorry no thrust data, but holding the unit in my hand produced impressive thrust for a 64mm fan. The website says 17.8 amps as 'load current'. If I understand that to mean max continuous, than a five blade fan may be better. No thrust data, but impressive for 64mm unit.

| Geverifieerde koper

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Apr 04, 2010

Awesome motor, 540W on peak with a 5*5 prop and a 3S 1600 35C hyperion.

Upload bestand

Registreer om bestanden te uploaden.
Alstublieft aanmelden of registreren om nu hobbyisten te helpen!