New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

Turnigy 3 Functie CDI Remote Master - Voltage Display - Receiver Switch (No BEC)

Turnigy 3 Functie CDI Remote Master - Voltage Display - Receiver Switch (No BEC)

Shipped From:
  • Global
Discontinued Product

Please continue searching for a similar product.
SKU:
373000006
WANT FREE SHIPPING? Click here to find out more!

Deze ontvanger switch beschikt over een ingebouwde ultra hoge helderheid LED-ontvanger accuspanning display, dat is duidelijk zichtbaar in direct zonlicht.

Daarnaast is deze schakelaar is uitgerust met een afstandsbediening CDI ontsteking hoofdschakelaar als een extra veiligheidsvoorziening voor gas engine gebruikers.

Onafhankelijke CDI macht en ontvanger voeding sockets. De ontvanger stroom volledig geïsoleerd van de CDI stroomcircuit, dus er is geen risico dat de CDI hoogfrequente signaal van de ontvanger zal bemoeien.

De ontvanger schakelaar zelf is beoordeeld als 15Amps continu.

Let op: Geen BEC - voltage input is gelijk aan uitgangsspanning

specs:
Kanalen: 1 (AUX) voor CDI Ontsteking Switch
Input Voltage: 5-6v
Schakel beperkingen: RX 15Amps; CDI 5Amps
Uitgangsspanning: Same as input
Gewicht: 42g
Volume: 40mm x 27mm x 35mm

  • Sku 373000006
  • Brand Turnigy
  • Capaciteit ( mAh ) -
  • Gewicht 65.0000
  • Lengte 105.00
  • Packaging Width 45.00
  • Hoogte 83.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Love the voltage display - never guess again. Bonus CDI control!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Love the voltage display - never guess again. Bonus CDI control!

1) It would be good solution to improve the way of solder wires. They should be better supported and isolated against vibration. Everyone, who decided to use this switch in their rc plane, before instalation, should use a drop of hot glue or silicone to hold wires in place.

2) switch's body, made of aluminium, is a little bit heavy. In case of bigger airplane, the place of instalation have to be reinforced and screws secured against becoming loose due to high vibration.

Those two points above are very important to avoid a troubles in the air !!!
I am telling this on the base of my own experience !!! I almost lost my 2m CAP232 due to broken wire.

3) The led indicator for CDI, visible in switch whole is hard to see, specialy in bright sun. It would be a best solution to place the led in better visible position on front panel (near display i.ex.), instead inside the switch.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

1) It would be good solution to improve the way of solder wires. They should be better supported and isolated against vibration. Everyone, who decided to use this switch in their rc plane, before instalation, should use a drop of hot glue or silicone to hold wires in place.

2) switch's body, made of aluminium, is a little bit heavy. In case of bigger airplane, the place of instalation have to be reinforced and screws secured against becoming loose due to high vibration.

Those two points above are very important to avoid a troubles in the air !!!
I am telling this on the base of my own experience !!! I almost lost my 2m CAP232 due to broken wire.

3) The led indicator for CDI, visible in switch whole is hard to see, specialy in bright sun. It would be a best solution to place the led in better visible position on front panel (near display i.ex.), instead inside the switch.

1 lack of crown on quality. the main switch is not perfectly soldered. The solder points are not hidden and it is.easy to fix.



I figured the function out, there is no manual available.



Connections:

1. Leftmost wire goes to rx. i.e. say channel 6.

2. 2:nd from left goes to a 4.8V radio battery or BEC (5 or 6V).

3. 3:rd from left goes to optional consumer. CDI, smoke pump, lights or whatever.

4. Rightmost wire goes to optional power supply. This one may possibly handle more than 6V .. will check that out soon .. would be nice if you could connect a 3S battery directly to power any cool stuff.



Function:

A. Main switch switches power from 2 to 1 and lits the voltage meter. The meter shows rx battery voltage.

B. The optional tx controlled switch is always off at startup regardless of the state tx switch is positioned. Guess that this is for safety reason and no ignition should be on at start up. The optional switch is then toggled from tx switch. Feels a little strange that on/off could be either way depending on first state of switch arm. A hidden LED behind the main switch is illuminated red when CDI power is on, could be visible in the main switch hole. If you like you may desolder this led and wire it to a more convenient location, but it works nice the way it is.



note. the remotely swiched output is 0.2V below its input voltage, a standard, completely normal t

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

1 lack of crown on quality. the main switch is not perfectly soldered. The solder points are not hidden and it is.easy to fix.



I figured the function out, there is no manual available.



Connections:

1. Leftmost wire goes to rx. i.e. say channel 6.

2. 2:nd from left goes to a 4.8V radio battery or BEC (5 or 6V).

3. 3:rd from left goes to optional consumer. CDI, smoke pump, lights or whatever.

4. Rightmost wire goes to optional power supply. This one may possibly handle more than 6V .. will check that out soon .. would be nice if you could connect a 3S battery directly to power any cool stuff.



Function:

A. Main switch switches power from 2 to 1 and lits the voltage meter. The meter shows rx battery voltage.

B. The optional tx controlled switch is always off at startup regardless of the state tx switch is positioned. Guess that this is for safety reason and no ignition should be on at start up. The optional switch is then toggled from tx switch. Feels a little strange that on/off could be either way depending on first state of switch arm. A hidden LED behind the main switch is illuminated red when CDI power is on, could be visible in the main switch hole. If you like you may desolder this led and wire it to a more convenient location, but it works nice the way it is.



note. the remotely swiched output is 0.2V below its input voltage, a standard, completely normal t

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!