Registreren

Product Finder

Instellingen

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Registreren
Shipped From:
  • USA

Turnigy 63-64-A 280Kv 65A Brushless Outrunner (52-30)

Turnigy 63-64-A 280Kv 65A Brushless Outrunner (52-30)

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Gewicht:
750 g
SKU:
TR63-64-A
Product
Omschrijving

Grote stroom voor uw grootschalige 3D-vliegtuig.
Goed voor vliegtuigen van 60inch in 3D vorm, 80inch voor sport / warbird of tot spanwijdte 100-inch voor trainer slow-fly soort vliegtuigen.
Uitstekende efficiëntie en solide prestatie!

Model: C63-64-A
Input Voltage: max. 37V (10S Li-po)
Kv: 280 rpm / V binnen 10%
Aantal beurt:   16 Delta

Max. efficiëntie stroom: 50A
Huidige capaciteit: 65A / 60s
Internal Resistance: 28 Mohm
Nullaststroom @ 7V: 2.16A
Afmetingen: 82mm x 63mm
Shaft diameter: 10mm / 0.39in
Gewicht met kabels: 640g / 22.58oz
Aantal polen / magneten: 14
Aanbevolen model gewicht: 5000 ~ 10.000 g / 176 ~ 352oz
Vermogen equivalent: 0,90-150 van de Gloed Engine
Stator Maat: 52-30

Product
Specifications

Aanvullende Informatie

  • Sku:
    TR63-64-A
  • Brand:
    Nvt
  • Gewicht ( g)
    750.00
  • Lengte
    0.00
  • Breedte:
    0.00
  • Hoogte:
    0.00
  • Kv ( tpm / v )
    280.00
  • Max Currents (A )
    50.00
  • Vermogen ( W):
    0.00
  • Lengte B ( mm ):
    82.00
  • Kan Lengte D ( mm )
    55.00
  • Max Voltage ( V )
    37.00
  • Shaft A ( mm ):
    10.00
  • Unit Weight (g):
    640
  • C Diameter ( mm )
    63.00
  • Totale lengte E ( mm )
    106.00
  • Resistance ( mh ):
    28.00
Community
Discussions
Rate&
Review

Schrijf je eigen recensie

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
There's no stock since november, does anyone know when stock arrive for this motor ? I need 2 motors to build an electric montain board.



see ya
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
fly this motor in a 2,4m an-2, with yeti spinn 99 on 8s 4000 turnigy with a 20x10 apc-e, weight complete 9,4kg. later i will try a 4 blade 18" varioprop for a better scale look. im sure you cant get more qualitiy for this money
i m verry happy with this combo, works well without any problems.

paul
www.mac-fly.eu
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very good engine! I use it for 1,8m CMPro Marathon 24. I have done about 50 flights. I broke a few propellers (bad landings) but engine is still working very well!!! I don't recommend rear mounting (after firewall) - bad vibrations!!! Front mounting (in front of firewall) works very well.

My setup is:

8S5000 mAh 25C Turnigy lipo

100A HV Sentilon Turnigy

18x10 (19x10) TGS Sport propeller

About 1,6-1,8 kW!!!

You can see it at: http://www.youtube.com/user/mariuszmariusz121?gl=PL&hl=pl
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Construction of this motor is very solid. This motor is so nice looking you will want to tuck it in at night! Here is my setup:



Sentillion 100A HV ESC - I really like this ESC (so far) for a few minutes run time and full throttle for a few seconds it barely gets warm.



Turnigy 2200mah 3s 20C batteries - I bought 9 of these. Wired 3 sets of 3 in series. 1 set = 9s 2200mah, 2 sets = 9s2p 4400mah, 3 sets = 9s3p 6600mah. I can mix and match these batteries however I want now. When I am not flying my big plane I can use these batteries in my smaller planes.



Turnigy 5a sbec (8-40v) - You need to buy a separate bec with the Sentillion ESC. This one works great.



TGS Sport 18x8E Precision propeller - I bought a couple of these because they were so cheap. Under $4 a piece. Nice prop.



9s1p - 1800 watts

9s2p - 2050 watts

9s3p - 2350 watts (I figure about 20lbs of thrust)



This setup seems to suit this motor very well. Motor and ESC do not get too warm. This should fly my 1/4 scale super cub very nicely with power to spare!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Bought one and installed on an Ultimate 90 conversion so far so good on 8s 4000mah with a 20 x 8 APC prop. Measured on a Watts meter it hits WOT @ 64.10 Amps peak and 1842.2 watts peak. The 4 stars is because they dont list the max watts :0( Hope it holds up
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
TRES BON MOTEUR RAPPORT QUALITE-PRIX
MONTE SUR UN JODEL GRAUPNER DE 2.20M AVEC 2 X 5S-5000 25C TURNIGY
HELICE GRAUPNER 20X10 ET CONTROLEUR 100A SENTILON, PUISSANCE EXTRA POUR TIRER UN PLANEUR DE 8KG.
CHAUFFE NORMALEMENT QUAND ON TIRE DEDANS.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Stats with 100 amp Sentillon ESC, 18 x 10 prop and 2 5C 5000 lipos.
At 25 amps, 880 watts, at 60 amps, 1950 watts. More than enough to fly a 1/4 scale, 16 lb Piper Cub like aircraft.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Nov 1 2010

Amazing motor Turnigy 65-64 one of the best Ive used. Powering a 78" WS Lancair 120 8s 4000Mah nano batt using a 16x10 APC prop
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I use this motor on my Seagull Super Decathlon .120, it pull 5kg with 8s and 17x8 FIALA wood propeller, the plane weight is 6kg.



about 10 minutes of classical aerobatic fly



http://www.rcgroups.com/forums/showthread.php?t=1331818#post16439610
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
It would be a 5 star, but my engine come with the "lenght B" out of specs because the bearing was not in the correct place. I had to open the engine and with a proper device, put it in place. After that, the dimension come to normal, and I powered it up. Happy with the product, but dissapointed with quality control. Still recomend the engine.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Productlabels

Gebruik spaties om verschillende labels te scheiden. Gebruik enkele aanhalingstekens (') voor zinnen.