Registreren

Product Finder

Instellingen

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Registreren

Turnigy e-aandrijving 4030/10

Turnigy e-aandrijving 4030/10

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Gewicht:
367 g
SKU:
e-drive-4030/10
Product
Omschrijving

Turnigy e-aandrijving 4030/10

Spec.
Aantal cellen:
4 ~ 7 x Li-Poly
RPM / V: 385
Max. efficiëntie stroom: 20-40 A (> 78%)
Geen belasting stroom: / 2.1 A
Huidige capaciteit: 50A / 60s
Afmetingen: 40x30 mm
Shaft diameter: 6 mm
Gewicht: 367g
Aanbevolen model gewicht: 3000 ~ 4450 g
Aanbevolen prop zonder versnellingsbak: 13 "-16"

Aanbevolen Setup.
14x7 Dunne prop met 5 ~ 6S die 4850g duw geeft.

Plane Type.
Trainer: tot 5500G
3D: tot 3000g
Sport / Aero / Warbird: 4000g
Eq: 0,60 IC glow engine



Alle motoren zijn onder andere propeller adapter, connectors en bevestigingsmateriaal.

Product
Specifications

Aanvullende Informatie

  • Sku:
    e-drive-4030/10
  • Brand:
    Nvt
  • Gewicht ( g)
    367.00
  • Lengte
    0.00
  • Breedte:
    0.00
  • Hoogte:
    0.00
  • Kv ( tpm / v )
    385.00
  • Unit Weight (g)
    367
  • Max Currents (A ):
    40.00
  • Resistance ( mh ):
    0.00
  • Max Voltage ( V )
    25.00
  • Vermogen ( W)
    0.00
  • Shaft A ( mm ):
    6.00
  • Lengte B ( mm ):
    70.00
  • C Diameter ( mm )
    49.00
  • Kan Lengte D ( mm )
    33.00
  • Totale lengte E ( mm ):
    83.00
Community
Discussions
Rate&
Review

Schrijf je eigen recensie

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Just finished some bench testing on this motor:

Rm: 0.047 ohm (measured between any two motor leads)

Kv: 348 to 376 [rpm/volt] depending on controller advance (4-30 degrees)

Io: 1.05 to 1.30 [amps] @ 12.6v depending on advance (4-30 degrees)



Motor came without connectors. Motor is well ballanced and has some flux leakage from the motor can. No funny noises. 12 tooth stator with a 14 pole rotor.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I just got this motor last week and have tested it with a few different props. I have it mounted on a .60 size P51 Mustang, at first I tried a 14 x 7 thin prop and got 7000 rpms on 6 lipos, I then tried a 14 x 7 APC and got around 6800 rpms. This would of been good on a lighter plane but this plane is pretty heavy. Then I tried a 15 x 12 on 6 lipos and that did the job. The only negative was the thin prop shaft on adapter and loose fitting nut.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I'm using the 4030/10 in a CMPro P-26 Peashooter. Batteri 6S 5000mAh Lipo and a 14/7 thin prop. The engine is pulling around 5 kg thrust and is running very smooth. Best buy at that price. 5 Stars from me
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very nice looking motor but it also has plenty of power! On my test stand I got the following results using my eagletree data loger:

Battery: 10S A123 2300mah cells 36V(all I had on hand for testing)

ESC: Turnigy Sentilon 100A HV

Prop: APCE 16X8

Full Throttle: 1200 watts @ 35amps

RPM works out to around 13,000 (batt voltage under load X KV of the motor)

After a 30 second full throttle run motor was warm but I wouldn't say hot at all. Next stop for this motor is the nose of my 4 meter sailplane!

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Just received this motor as a replacement for the other one I have. I just wanted the prop mount adapter because the threads stripped on the previous one. NOW THIS ONE stripped too. this a serious design flaw. I do not recommend this to anyone else unless you want to have your plane to had a prop strip in mid flight.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
First. 6s at 375kv max RPM is 8250 - NEVER 14x7 prop and 5 rg thrust!!!



I use this motor with 6s 4250mA + Turnigy Plush 80 with 14x7 thin prop - above 2.3 kg thrust. APC-E 16x8 and 15x10 props give 3-3.2 kg thrust and maximum 32...34A... Hmmm... I whant more! But I can not use more than 6s....



HobbyKing! What prop give 4 kg thrust on this motor and 6s?
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Productlabels

Gebruik spaties om verschillende labels te scheiden. Gebruik enkele aanhalingstekens (') voor zinnen.