Tonen : ALLE CATEGORIEËN 0 Vliegtuig 1926 Drones 678 Framekits voor drones 17

Turnigy Integrated PCB Micro-Quad (KIT)

Turnigy Integrated PCB Micro-Quad (KIT)

56 Recensie

Prijs:

Now save bespaar € 0,00 € 0,00

€ 18,13

Al gekocht Discontinued Product

Please continue searching for a similar product.

SKU:

9332000001

Geen verzendkosten? Klik hier meer leren!

Deel dit product en verdien 94 punten (€ 0,91) [ ? ]

Product beschrijving

Deze kleine maar briljant ontworpen micro-Quad beschikt over een geïntegreerde PCB frame, gewoon bout op de motoren dan soldeer uw keuze van 6A ESC direct aan het frame!

Een geïntegreerde stroomverdeling systeem is ook opgenomen voor het maken van een van de leukste elektronica installeert rond. Alle bevestigingsmateriaal en het frame onderdelen zijn opgenomen in de kit. Alles wat u nodig heeft om dit kleine monster in de lucht te hebben, is vier Turnigy T1811-2900kv motoren, vier 6A SER, een set van 5x3 Micro-quad props (2 klok wijs en 2 tegen de klok in) een 800mAh 2s 7.4V LiPoly batterij, een HobbyKing Multi-rotor control board en je eigen zender en ontvanger (Tx / Rx).

Kenmerken:
Lichtgewicht ontwerp.
Geïntegreerde printplaat voor de installatie van onderdelen.
Inclusief een volledige set van frame en bevestigingsmateriaal.

specs:
Flying Gewicht: 145g (exclusief RX en batterij)
Breedte: 250mm
Lengte: 85mm

Vereiste:
4 x Turnigy T1811-2900kv
4 x 6A ESC
4 x 5x3 Prop (2CW & 2CCW)
1 x HobbyKing Multi-Rotor Control Board
1 x 800mAh 2s 7.4V LiPoly batterij
16 x M2x8 Bouten (voor motor)
16 x M2 borgmoeren (voor motor)
Uw eigen radio en 4 kanaals ontvanger.

Product specificaties

Videos

Upload video

Registreer u om video's te uploaden aanmelden of registreren

Bespreken 0

Onderwerpen

Sorteer op

Meest recente onderwerpen

Plaats een nieuw onderwerp

Recensie

Registreer u om beoordelingen te schrijven aanmelden of registreren

Adam | Geverifieerde koper

Overall
Quality
Value

Customer Rated

Feb 14, 2014

This PCB frame is a piece of crap. It could not survive 30cm fall - after that one motor mount was broken.
This construction has a major design flaw: the hole for motor wires are placed inline with the end of the ribs - which are too short and to thin.

Maybe my frame was faulty, but when You look closer this is not sturdy FR-4

If You must have a microquad, go buy black one with integrated ESC and BEC

ERIC | Geverifieerde koper

Overall
Quality
Value

Customer Rated

Jul 09, 2013

Flew great until I crashed it from 5 feet off the ground. The motor mount is not sturdy and broke clean off. The motor mount design saved a 50 cent prop but cost me a 15 dollar frame.

Insaniac | Geverifieerde koper

Overall
Quality
Value

Certified Buyer Rated

May 22, 2013

Fun little quad but kind of a pain to do all that soldering. 34 of them all together including the battery connecter. Plenty of room for a 50mm FC and RX. Indoor flyer for sure.

dvogonen | Geverifieerde koper

Overall
Quality
Value

Customer Rated

May 16, 2013

It is well made and all, but the construction is deeply flawed. The motor mounts will break off at first impact, since someone made the bad decision to put a hole at the thinnest point. There are only a few millimeters of PCB on each side of the hole. You can easily snap it off without applying much force at all.
If you glue something on top of the hole, the complete arm will break off at the base, tearing the copper laminate. It is easy enough to repair with thin CA and some jumper wires, but the repaired places breaks even easier.
I strongly suggest building your own frame out of some scrap plywood and four 1/16 (8mm) wood spars or buying a more robust frame kit.

muddyfox | Geverifieerde koper

Overall
Quality
Value

Customer Rated

May 01, 2013

Great PCB frame, lightweight with the 1811 - 2900 motors, 5x3 props, KK2 FCB, 2S 800mAh LiPo. About 6 min flight time indoors and fast and mild acro outdoors with 6 mins. I will get a 1300 mAh 2S with my next order, the little beast can handle these LiPos easily. Great for any place at any time flying and having fun.

| Geverifieerde koper

Overall
Quality
Value

Certified Buyer Rated

Apr 13, 2013

very good quad ! good shipping

bisky | Geverifieerde koper

Overall
Quality
Value

Certified Buyer Rated

Jan 19, 2013

Good frame kit, easy to assemble, werry helpful with the onboard pcb for power destribution. Did not fly yet because of propeler problems, hope to get it in the air soon.

ANARIT-119 | Geverifieerde koper

Overall
Quality
Value

Certified Buyer Rated

Jan 12, 2013

nice and small quad... nice to fly indoors... really impress with the way it was packed!!!

MacRaven | Geverifieerde koper

Overall
Quality
Value

Certified Buyer Rated

Jan 07, 2013

Cool Gadget this Frame but the Motor Extensions are a bit fragile. Just Stiffen the end connections with 2k Epoxy and nothing will break. Even with hard Landings.

| Geverifieerde koper

Overall
Quality
Value

Certified Buyer Rated

Dec 04, 2012

This little frame is delivered in a surprisingly flat envelope! It may seem a bit fragile at first but some of the pieces interlock and a few drops of CA later the frame is quite sturdy.

I like the dome on top that will protect your control board in the event of a crash.

I also like the bars between the legs of the structure where you can easily strap a battery.