Turnigy Multistar USB BLHeli programmeur voor V2 Multistar ESC

• Overall
• Quality
• Value

It works as intended, but minus one point for the lack of instructions.

Apr 22, 2018

Ironically, I came here to give it a bad review due to lack of instructions, and then I found the instructions I needed in the reviews. It works as intended, but minus one point for the lack of instructions.

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 04, 2016

turnigy buenos productos y bajo costos

• Overall
• Quality
• Value

Certified Buyer Rated

Sep 30, 2015

Fantastic item, I use it all the time in all places and electronics. Nice n shiny finish, good covering finish.

• Overall
• Quality
• Value

Customer Rated

Sep 29, 2015

LHeli with 15A Multistar ESC with Multistar USB Tool

- BLHeli: https://blhelisuite.wordpress.com/

- Multistar USB Tool with out reed wiere!

- De Multistar ESC feed with 5Volt from ext.BEC!

-
Settings BLHeli

1. install the driver

2. start BLHeli Suite

3. Select Amtel/Silabs Interface = 1 Amtel BLHeli Bootlader (USB/Com)

4. Plug in USB programmer into your computer

5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]

6. Select the correct speed (Baud 9600)

7. Connect ESC plug into USB programmer (without the red cable !!!)

8. Click on Connect

9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)
-
Eanable One Shot in BL Heli


- PWM Frequency/Damping = Light

- Motor Timing = High

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 06, 2015

Einwandfreie Funktion mit den 6A V2 Reglern.

• Overall
• Quality
• Value

Customer Rated

Feb 03, 2015

Works fine.
I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire of the USB programmer and to power the ESC from a BEC 5V.

Procedure (to combine with LeBobo's MultistarV2 Pack ) :
1. install the driver
2. start BLHeli Suite
3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
4. Plug in USB programmer into your computer
5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
6. Select the correct speed (Baud 9600)
7. Connect ESC plug into USB programmer (without the red cable !!!)
8. Click on Connect
9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

• Overall
• Quality
• Value

Customer Rated

Feb 03, 2015

Works fine.
I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire and power the ESC from a BEC.

Procedure (to combine with LeBobo's MultistarV2 Pack ) :
1. install the driver
2. start BLHeli Suite
3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
4. Plug in USB programmer into your computer
5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
6. Select the correct speed (Baud 9600)
7. Connect ESC plug into USB programmer (without the red cable !!!)
8. Click on Connect
9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

• Overall
• Quality
• Value

Certified Buyer Rated

Jan 14, 2015

I use this USB programmer with Multistar 10A and I haven't got any problem.

• Overall
• Quality
• Value

Customer Rated

Dec 06, 2014

It is not a programmer for Multistar, it is a universal programmer from Multistar.
The stick has always worked with BLHeliSuite, with ANY Atmel based ESC, which has the small 512 bytes BLHeli bootloader flashed over ISP (and which do not have an inverted input, like the Multistar V1 ESC have). It has NOT been specially build for Multistar ESC nor is it somehow bound to work only with Multistar ESC.
All the negative reviews address the Multistar V2 ESC, not the this Multistar programmer.
As far, as it tested, it works great and is easy to use.
The best solderless ready-built adapter for the small 512 bytes BLHeli bootloader (or other 1-Wire AVRootloader solution).