New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

Turnigy Voltage Protector 783333uf (3 sec)

Turnigy Voltage Protector 783333uf (3 sec)

Shipped From:
  • Global
QTY:

Now save bewaar € 0,00 € 0,00

€ 5,37
status:
In voorraad
SKU:
VPCAP47
WANT FREE SHIPPING? Click here to find out more!

De Turnigy capaciteit set helpt voorkomen "brown-outs" resetten Rx als uw servo amp draw spikes of je hebt een Rx glitch.
Het zal ook helpen verminderde de belasting op uw SER BEC en de kans op glitching verminderen. Gewoon de stekker in om eventuele reserve-kanaal op je ontvanger.

Werkend Voltage: 3.2V - 11.1V (1s ~ 3s LiPo)
Condensator voltage: 15v
Opslagcapaciteit: 783333uf
Gewicht: 26,2 g

Gegevens over een 3A belasting piek meestal gezien als grote terugtrekt jam:
Supply 6v met een spanning dalen tot 4.7V dan 0.88sec
Supply 6v met een spanning dalen tot 3,0 V meer dan 3.0sec (3.0V minimale spanning van de OrangeRx 6ch)

  • Sku VPCAP47
  • Brand Turnigy
  • Capaciteit ( mAh ) -
  • Gewicht 35.0000
  • Lengte 55.00
  • Breedte 25.00
  • Hoogte 40.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Bei 2,4 GHZ gehört es an den Empfänger.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Bei 2,4 GHZ gehört es an den Empfänger.

its bunch of 2.5v 4.7F capacity.

so you can use it under 15v.

however, it makes servo get crazy when you turn off reciver. so its bad for servo condition.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

its bunch of 2.5v 4.7F capacity.

so you can use it under 15v.

however, it makes servo get crazy when you turn off reciver. so its bad for servo condition.

It works perfect, but for a 450 Size Heli i little bit to Big so i will try the smaller one. And on this i will safe the two Cables out of the Circuit Board with a little bit of Hot Glue, to prevent loosening ...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

It works perfect, but for a 450 Size Heli i little bit to Big so i will try the smaller one. And on this i will safe the two Cables out of the Circuit Board with a little bit of Hot Glue, to prevent loosening ...

nice item. It exceeded the specs listed.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

nice item. It exceeded the specs listed.

So I plugged it into a spare port on the receiver in my plane with 2 servos plugged in. After being plugged in for 5 minutes which should be enough for it to charge up, I unplugged my battery. I was able to wiggle my servos for about 4 seconds, and then the servos both locked in one direction. Granted, this is with 2 servos so if you have a full setup you only have maybe 2 seconds so you better hope you're just in a situation where your esc just restarted, rather than your esc or bec burning out altogether

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

So I plugged it into a spare port on the receiver in my plane with 2 servos plugged in. After being plugged in for 5 minutes which should be enough for it to charge up, I unplugged my battery. I was able to wiggle my servos for about 4 seconds, and then the servos both locked in one direction. Granted, this is with 2 servos so if you have a full setup you only have maybe 2 seconds so you better hope you're just in a situation where your esc just restarted, rather than your esc or bec burning out altogether

main problem in combination with an Quanum Nova is that the Protector is to big to store it in the Nova Cover. but with a little modding it will fits... But Protector works well!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

main problem in combination with an Quanum Nova is that the Protector is to big to store it in the Nova Cover. but with a little modding it will fits... But Protector works well!

Hab den als Spitzenstromgltter in einem 2S LiFePo HV setup im Hubi. Wegen des hohen Anlaufstromes hab ich zwei Schalter. Der erste schaltet ber einen Widerstand von 10 Ohm nur das Ding an den Akku( daran hngt das kleine Voltmeter ( Artikel nr.067000001) , Wenn Spannung da, wird der Empnger mit einem zweiten Schalter zugeschaltet. Schaltung ist ein wenig tricky, geht aber. Ich nehme dazu einen Doppelschalter und einen dreifach zur Sicherheit. zwei von dem Dreifach gehen wie der erste doppel zum Empfnger, einer dient nur der Vorladung des Kondensators. Wenn jemand ein Schaltbild davon bentigt, mge er mir Nachricht geben. Klappt super.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Hab den als Spitzenstromgltter in einem 2S LiFePo HV setup im Hubi. Wegen des hohen Anlaufstromes hab ich zwei Schalter. Der erste schaltet ber einen Widerstand von 10 Ohm nur das Ding an den Akku( daran hngt das kleine Voltmeter ( Artikel nr.067000001) , Wenn Spannung da, wird der Empnger mit einem zweiten Schalter zugeschaltet. Schaltung ist ein wenig tricky, geht aber. Ich nehme dazu einen Doppelschalter und einen dreifach zur Sicherheit. zwei von dem Dreifach gehen wie der erste doppel zum Empfnger, einer dient nur der Vorladung des Kondensators. Wenn jemand ein Schaltbild davon bentigt, mge er mir Nachricht geben. Klappt super.

Utilissimo per evitare sbalzi nella tensione di alimentazione dell'elettronica. Molto leggero

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Utilissimo per evitare sbalzi nella tensione di alimentazione dell'elettronica. Molto leggero

I will use, not installed yet, but has a good quality for sure... Thnaks HK

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I will use, not installed yet, but has a good quality for sure... Thnaks HK

They buffer my CC ICE BEC really well, I changed it from the 6s to a 3s2p setup. Now the CC ICE BEC delivers 5A as it should.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

They buffer my CC ICE BEC really well, I changed it from the 6s to a 3s2p setup. Now the CC ICE BEC delivers 5A as it should.

  1. 1
  2. 2
Customer files
Supercapacitor Download [208]
Supercap datasheet Download [94]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!