New Items Forum
Registreren

Total Price

€ 0,00

Winkelwagen 0 Winkelwagen 0 Loading...

Turnigy ™ TGY-D56MG Coreless DS / MG HV Servo 1.2kg / 0.10sec / 5,6 g

Turnigy ™ TGY-D56MG Coreless DS / MG HV Servo 1.2kg / 0.10sec / 5,6 g

Shipped From:
  • USA
  • Global
QTY:

Now save bewaar € 0,00 € 0,00

€ 6,68
status:
In voorraad
Gewicht:
17 g
SKU:
9399000023-0
WANT FREE SHIPPING? Click here to find out more!

De Turnigy D56MG HV is ideaal voor kleine 3D-vliegtuigen en parkflyers waar de robuustheid van een metal gear trein is vereist. De kernloze motor zorgt voor een uitstekende houdkracht en precisie op een geweldige prijs. De HV spanning kunt u een 2s Lipo batterij of het leven direct te gebruiken zonder de noodzaak van een BEC.

specs:
Gewicht: 5,6 g
Afmetingen: 19.8x8.2x21.2mm
Stall koppel: .85kg / cm (4.8V) - 1,2 kg / cm (7,4 V)
Operating snelheid: 0.14sec / 60degree (4,8 V) - 0.1sec / 60degree (7.4V)
Werkspanning: 4.8-7.4V
Servo Plug: JR (Past JR en Futaba)

  • Sku 9399000023-0
  • Brand Turnigy
  • Gewicht ( g) 17.00
  • Lengte 90.00
  • Breedte 20.00
  • Hoogte 50.00
  • Torque ( kg) ( min . 0,01 kg ) 1.20
  • Snelheid ( Sec / 60deg ) 0.10
  • A ( mm ) 27.00
  • B ( mm ) 20.00
  • C ( mm ) 24.00
  • D ( mm ) 8.20
  • E ( mm ) 28.00
  • F ( mm ) 16.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

very small servo and light wegiht. also it can handle "high voltage" you can use this widely.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

very small servo and light wegiht. also it can handle "high voltage" you can use this widely.

This servo is poor quality, and not worth it's price.

I've tested the servo with the HobbyKing LED servo tester and when the servo reaches the extreme signal of 230 it stays locked (jammed) in the extreme position. The good quality servo should not lock up when extreme signal is received.

I initially intended to use these servos for my fixed wing, but knowing the nature of the failure I would not recommend anyone to use these on the air frames of any kind.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This servo is poor quality, and not worth it's price.

I've tested the servo with the HobbyKing LED servo tester and when the servo reaches the extreme signal of 230 it stays locked (jammed) in the extreme position. The good quality servo should not lock up when extreme signal is received.

I initially intended to use these servos for my fixed wing, but knowing the nature of the failure I would not recommend anyone to use these on the air frames of any kind.

I have installed quite a few of these in some mini FPV wings that I built for me and some friends of mine. All have worked out super well. Running them at 5V off the BEC of a 12A ESC.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I have installed quite a few of these in some mini FPV wings that I built for me and some friends of mine. All have worked out super well. Running them at 5V off the BEC of a 12A ESC.

1A Servos.
Benutze die Servos an einen 2S-Lipo. Habe aber zur Sicherheit immer eine Diode 1N4001 in Reihe vor jedes Servo geltet.
Die Servos haben eine ausgezeichnete Rckstellgenauigkeit, kein Spiel und fr ihre Gre
enorm viel Kraft.
Absolut zu empfehlen.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

1A Servos.
Benutze die Servos an einen 2S-Lipo. Habe aber zur Sicherheit immer eine Diode 1N4001 in Reihe vor jedes Servo geltet.
Die Servos haben eine ausgezeichnete Rckstellgenauigkeit, kein Spiel und fr ihre Gre
enorm viel Kraft.
Absolut zu empfehlen.

These Turnigy DSGMG servos appear to be well made. I bought four of them for their "HV" capability to use in a HobbyKing DLG. Apart from the motor pinion and its mating gear which were nylon, the remaining gear-train is all aluminium.

I used a two cell 300mAh Turnigy LiPo to power the two servo set-up in my DLG. Both servos failed within five minutes of powering-up. They ceased to work accompanied by a burning smell. A very disappointing result, hence the poor score.
Mark S.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

These Turnigy DSGMG servos appear to be well made. I bought four of them for their "HV" capability to use in a HobbyKing DLG. Apart from the motor pinion and its mating gear which were nylon, the remaining gear-train is all aluminium.

I used a two cell 300mAh Turnigy LiPo to power the two servo set-up in my DLG. Both servos failed within five minutes of powering-up. They ceased to work accompanied by a burning smell. A very disappointing result, hence the poor score.
Mark S.

je les ai achet? pour mon Extra 300L 3D et j'ai peu qu'il soit un peu faiblard et en, plus je les trouve lents

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

je les ai achet? pour mon Extra 300L 3D et j'ai peu qu'il soit un peu faiblard et en, plus je les trouve lents

Received these servo's yesterday, tested them right away because I was not completely confident that they would function on 2S (there are some messages about them burning on 2S - 8,4V and the technical data on the Hobbyking site and the packaging of the servo state an operating voltage up to 7,4V). First test on 5V with a BEC, than on 6V with BEC, after that on 7,4V on a half charged 2S battery without BEC and final test with fully charged 2S battery. The servo's held up great but are a bit slow on 5V. On 8,4 Volt they rock, very strong, fast and accurate! Going to build them in my Binary V2 DLG. Total weight of the electronics (diversity 6CH LemonRX, 260mAh battery and the three servo's) below 40 grams. Looks promising.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Received these servo's yesterday, tested them right away because I was not completely confident that they would function on 2S (there are some messages about them burning on 2S - 8,4V and the technical data on the Hobbyking site and the packaging of the servo state an operating voltage up to 7,4V). First test on 5V with a BEC, than on 6V with BEC, after that on 7,4V on a half charged 2S battery without BEC and final test with fully charged 2S battery. The servo's held up great but are a bit slow on 5V. On 8,4 Volt they rock, very strong, fast and accurate! Going to build them in my Binary V2 DLG. Total weight of the electronics (diversity 6CH LemonRX, 260mAh battery and the three servo's) below 40 grams. Looks promising.

Very Great Servo! Using these on my FT Might Mini Arrow.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very Great Servo! Using these on my FT Might Mini Arrow.

this is an awesome servo. very strong and accurate for its size. which makes it perfect for small park flyer models (I put them in my bonsai) or where size is a problem such as bomb bay doors or flaps where the servo is in the wing. would definitely recommend these and I will be buying more for future models or t have around as spares.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

this is an awesome servo. very strong and accurate for its size. which makes it perfect for small park flyer models (I put them in my bonsai) or where size is a problem such as bomb bay doors or flaps where the servo is in the wing. would definitely recommend these and I will be buying more for future models or t have around as spares.

Wer 2s fhige DLG Servos sucht wird hier bitter enttuscht!

Hab mir 6 von diesen Servos bestellt und habe 2 davon an 2S Lipo getestet. Ergebnis: Beide reif fr die Tonne... Die brigen 4 habe ich ber ein 2A Bec zu 6 Volt getestet und die gehen noch, allerdings ist mir die Spannung beim Anschlu des 4en Servos die Spannung eingebrochen was ja irgendwie nicht sein kann(oder ziehen die Dinger bei 0 Last mehr als 2A!!). Wie dem auch sei, mein Fazit ist: Nicht verwenden, definitiv nicht 2S fest. Finger weg

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Wer 2s fhige DLG Servos sucht wird hier bitter enttuscht!

Hab mir 6 von diesen Servos bestellt und habe 2 davon an 2S Lipo getestet. Ergebnis: Beide reif fr die Tonne... Die brigen 4 habe ich ber ein 2A Bec zu 6 Volt getestet und die gehen noch, allerdings ist mir die Spannung beim Anschlu des 4en Servos die Spannung eingebrochen was ja irgendwie nicht sein kann(oder ziehen die Dinger bei 0 Last mehr als 2A!!). Wie dem auch sei, mein Fazit ist: Nicht verwenden, definitiv nicht 2S fest. Finger weg

  1. 1
  2. 2
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save