Registreren

Product Finder

Instellingen

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Registreren

Variabele spoed prop & motor set 9 "Type B

Variabele spoed prop & motor set 9 "Type B

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Gewicht:
200 g
SKU:
OR025-02003
Product
Omschrijving

Deze eenvoudig te installeren apparaat zal u toelaten om de toonhoogte van uw prop motor achteruit TIJDENS DE VLUCHT! De lijst van mogelijke manoeuvres is eindeloos! De unit bestaat uit 2 9 "bladen en outrunner motor, en de variabele spoed te monteren. U zult een servo nodig om de toonhoogte montage te controleren.

Spec.
Motor: D3123-1600kv
Voltage: 11.1V
Gewicht: (ongeveer) 43 g
Prop: 9inch

Product
Specifications

Aanvullende Informatie

  • Sku:
    OR025-02003
  • Brand:
    Nvt
  • Gewicht ( g)
    200.00
  • Lengte
    162.00
  • Breedte:
    45.00
  • Hoogte:
    57.00
  • Kv ( tpm / v )
    1600.00
  • Max Currents (A )
    0.00
  • Vermogen ( W):
    0.00
  • Lengte B ( mm ):
    24.00
  • Kan Lengte D ( mm )
    9.00
  • Max Voltage ( V )
    11.00
  • Shaft A ( mm ):
    4.00
  • Unit Weight (g):
    43
  • C Diameter ( mm )
    30.00
  • Totale lengte E ( mm )
    45.00
  • Resistance ( mh ):
    0.00
Community
Discussions
Rate&
Review

Schrijf je eigen recensie

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
The motors are pretty decent but the prop assemblies are DANGEROUSLY LOW QUALITY! During a static test on a 3 cell one of the plastic prop mounts broke at high rpm and sent shards of plastic flying across the room and also sent the motor flying. The problem is that the prop grabbers are far too weak, and the screws which hold the blades on are so weak that they were bending. The balance was pretty far off too. I will be replacing the prop assemblies with electrifly ones, however the motors are decent so I will be keeping them. BE CAREFUL! could have easily taken an eye out.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very dangerous product. Blades flew out because the screws they gave are too short to hold them, resulting in the screw tip undoing itself. I lost a blade because of this.

The second time, I used a longer screw with a nut, but the entire screw sheared outwards due to the centrifugal force. The blade holders are dangerous because they're made of plastic. You've been warned!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Great unit, excellent value!

I received my prop and motor a few days ago, and I can say it is excellent!
Let me tell you what it can do.
Firstly, you know the pitch is reversible, but so are the blades. You could easily set this up to run as a puller or a pusher, and run it either direction, with a few adjustments or wire flips. I have only bench tested mine so far, but it is very strong for it's size. I have tested it on a 3s lipo pack, and it throws a lot of wind.

I am setting mine up for an air rescue boat, so it will be used forward and reverse pitch, and used in a pusher style. So far so good.

They said the blades are 9 inch, but when assembled, the prop measures 10 and a half inches, just remember that when you are getting it set up to your model. The windings in the motor look good, and wound pretty well.

The pitch mechanism works well, but is all plastic, so I would expect wear issues from it. I bought 2 more for parts and to experiment some. It will take another motor, simple by taking the motor off the prop, and getting another hollow shaft motor. I would think this will run fine on a 2s, but I am running 3s. When pulling or pushing on the control, it will put significant resistance on the shaft, but this is because the wind from the prop tries to push it back to neutral. A 9g servo won't cut it, unless you set it with a short throw. You can compensate
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Just bought one identical on ebay, same price and everything, this has got to be the retailer!!!!! This one Has a removable engine. I'll take this one and tell all my friends thanks. To change the engine just loosen a set screw, holding the engine on. Then if you got a biggerhollow tube brushless, us that one. To Easy!! As for spare parts, I'll raid my heli for a spare part out on the field in a pinch!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Nice system, especially for the price!!

But it's realy heavy.

The engine runs nice, but with a little inbalance.

i think a 2s battery should be good enough, with the 3s it gives a realy high RPM in neutral.

The pictch is realy hard to change at high RPM, youll need a big servo (HXT900??)

It realy eats batterys. it got my 2s 2100mAh warm!

I cant wait to test it in the air!!
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Productlabels

Gebruik spaties om verschillende labels te scheiden. Gebruik enkele aanhalingstekens (') voor zinnen.