-
Product
Omschrijving -
X-UAV introduceert de Lotus, een schuim gestructureerde quadcopter met ingebouwde propeller bewakers, water landing praalwagens en een 360 graden duidelijk camera koepel.
Het schuim structuur met geïntegreerde kader maakt deze quad zeer duurzaam en licht. Het landingsgestel fungeert ook als drijvers, waardoor de quad de mogelijkheid om veilig te vliegen en land op het water. De grote waterdichte centrum bay kan gemakkelijk het huis van alle kritische elektronica en de batterij, waardoor ze mooi en droog. De andere grote eigenschap over het schuim constructie is de ingebouwde propeller bewakers waardoor dit een van de veiligste frames voor bepaalde toepassingen. En het zou niet een X-uav zijn zonder een 360deg bodem geplaatste optische Dome voor uw camera.
Kenmerken:
• lichtgewicht schuimstructuur
• water drijft en waterdicht center bay
• Ingebouwde prop bewakers
• Duurzaamheid en veiligheid
• 360 duidelijke bodem dome voor cameraspecs:
Wielbasis: 450
Grootte: 740x740x160mm
Gewicht: 515gVereiste:
4 x 2212 ~ 4006 klasse motoren en paste ESC
4 x 8 ~ 9 inch propellers
Flight controller
5ch Radio
Accu -
Product
Specifications -
Aanvullende Informatie
-
Sku:
239000004-0
-
Brand:
Nee
-
Capaciteit ( mAh )
Nee
-
Gewicht ( g)
3134.00
-
Lengte:
660.00
-
Breedte:
175.00
-
Hoogte
655.00
-
Sku:
-
Community
Discussions -
-
Rate&
Review -
This is by far NOT for the inexperienced builder. Space, or lack thereof is THE main issue of the build. One would need to be prudent about the physical size of ESC used the length of motor cables and battery size. I had to remove & replace the plywood base tray 3 times in order to get it right. I am using a servo-op cam for tilt and whiles there ample room below the lower dome for such a mod, above it is a whole other story. One needs to measure your motor cables accurately as bundling up wires wont work. Use a pwr dist board to help save space, I mounted mine to the ply base and used nylon spacers to mount a CF board which acted as a sandwich where between the ESC sit. I then mounted my NAZA/PMU/4S LiPo on that. TIGHT FIT ! FPV Tx sits outside on frame pwr by dist board. Using Multistar 4000 4S Green LiPo I get 9 minutes swinging 0945 3 blade props on DIY Drone blue motors. Great flying machine in configuration REALLY HAPPY as its a tough little Quad too, Many intentional crashes and almost no serious damage only foam cracked on rotor guard once but poly skeleton is super tough ! Buy Build & Fly...Ps AUFW=1650gSto installando 4 T motor 2216 con eliche apc da 10" riscontrando che queste sono a rischio, ruotano a filo supporto, anche volendo montare eliche pi piccole, il problema non si risolve perch esse flettono rischiando di impattare con il supporto motore a 4 punti di fissaggio.
Deluso lo sconsiglio, spero che modifichino tale problema che rende il frame impossibile da utilizzare. -
Upload
Videos -
Upload
Files
- esc
- battery
-
-
Pack Multistar High Capacity 3S 5200mAh Multi-Rotor Lipo
Special Price € 21,36
You save € 5,87
Was € 27,23
-
Pack Multistar High Capacity 3S 4000mAh Multi-Rotor Lipo
Special Price € 13,41
You save € 3,70
Was € 17,11
-
Pack Multistar High Capacity 4S 5200mAh Multi-Rotor Lipo
Special Price € 23,45
You save € 10,72
Was € 34,17
-
Pack Multistar High Capacity 4S 4000mAh Multi-Rotor Lipo
Special Price € 13,99
You save € 9,79
Was € 23,78
-
- motor
-
-
NTM Prop Drive 28-26 1000KV / 235W (korte schacht versie)
€ 12,17 -
Turnigy Multistar 2216-800Kv 14Pole Multi-Rotor Outrunner
€ 14,52 -
AX-2810Q-750KV borstelloze Quadcopter Motor
€ 16,90 -
Turnigy Multistar 3525-850Kv 14Pole Multi-Rotor Outrunner
€ 23,64 -
Turnigy Multistar 2814-700Kv 14Pole Multi-Rotor Outrunner
€ 23,09
-
- acc