Dit stijlvolle mini quad is een geweldige manier in multi-rotor vliegtuigen te krijgen zonder het gedoe van het kiezen van je eigen kracht systeem! Gebouwd van glasvezel, dit frame is zowel licht van gewicht en sterk.
Deze kit bevat de motoren, SER en propellers, dus je hoeft alleen maar je eigen multi-rotor control board, radio-systeem en de batterij toe te voegen. Het beschikt ook over een stroomverdeling boord om de bedrading netjes te houden.
Wij voeren een volledige lijn van multi-rotor controle boards om uw kit te voltooien, moet u de gerelateerde items hieronder.
* Opmerking: De bovenstaande foto's zijn ter illustratie van alleen het eindproduct. U moet de motoren, SER's zelf te installeren en soldeer de stroomverdeling board.
Flying Gewicht: 315g (exclusief RX en batterij)
Multi-rotor vlucht controller
4CH zender / ontvanger
3S 11.1V 1000 ~ 1500mAh batterij LiPoly
Gewicht ( g)
My advice: don't buy.
Had to buy and replace all ESCs by myself (the default ZTW ones were all broken and lead to sudden motor failure and stuttering).
HobbyKing does NOT have any spareparts in stock.
Motors are mounted in a stupid way.
If the landing is a little bit rough, the props crash against the frame and destroy themselves (had this 5 times already).
Bad frame construction:
* battery does not align with flight direction (rotated 45 degrees against flight direction)
* motors are mounted in such a way that it is almost impossible to fix the props as low to the motor as possible
There is no information available about the built in motors or what could be used as replacement.Cheap and easy to build. Lack of instructions and information about the parts but it is ggod start for mini multicopters.Not a bad quad but I have to say it lacks in the power department. The props are incredibly flimsy so I am hoping when I change them to carbon fibre it might help the problem. The instructions where relatively clear and it went together without any problems. This is my fourth quad, I wanted something small I could fly around the back yard. there are also no spare parts available which could be a problem for new pilots in the event of a crashHello, I need help for the esc setup. According to the manual I got ztw 12amp escs with the kit. So foolowing the manual i wanted to make some changes but the tones what i supposed to follow are absolutely different. My escs has no label and at the moment im not sure that these are ztw. If not what esle they are? I hope you can help becouse without any label hard to tell the make and find a correct programming guide. The only thing what I know that they are black. :) Thanks, Peterit is a very nice small quad. it is easy to to put together although the power board could be tricky. i have to point one problem which is the props i broke mine and i can't find replacement now..Just one word ! WOW GG KHeasy to put together instructions ok problem with one motor it keeps stuttering and not running properly have swapped escs and still same,now have done direct solder joints but still not much better ,what i have ended up with is a copter which has no spare parts availability and not always flyable ,and not returnable as i have modified itAbsolut genial,
ist mein erster Copter. Komme ganz gut damit klar.
Meiner Meinung nach Ideal zum anfangen.
Fliege momentan mit 3S 1300 Lipo,
werde auf 1800 3S umsteigen.
Habe noch LEDs eingebaut, geil!!!My first quadrotor. Goes together quickly and flys well. Initially used I86 controller and now upgraded to MultiWii MicroWii ATmega32U4 which fits the mounting holes. Due to this quadrotors small square base, it's prone to tipping over on landing so after a few broken props, I have added helicopter style training base (ie carbon rods with foam balls at ends). This makes it far more stable on landing.Very nice. Bought and love it! Very strong. Use it with a Multiwii Pro . Assemled a small glass fiber 2 axis gimbal for gopro hero 3 to put on it. Flies very well. 5min autonomy.
x230wKK2 download now [71kb] x230wFoamShell download now [58kb] FoamShell1 download now [75kb] FoamShell2 download now [48kb] Motrax X230 modified detail download now [409kb] ZTW ESC manual download now [348kb] Motrax X230 download now [1297kb] Power board ready download now [480kb] Motrax power board download now [882kb] Motrax X230 modified download now [449kb] Heli Skid Mod download now [2246kb] power distribution board and bottom plat download now [1934kb] X230 USER MANUAL download now [553kb] X230 w/328P download now [600kb] x230 Finished Product download now [212kb] Louis' distribution board download now [1348kb]