XK2845-B-3700KV borstelloze Inrunner

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 26, 2015

Very powerful motor for mini rc cars (1/16). Quality is great for the price and time will tell how this will handle good bashing. Recommend!

• Overall
• Quality
• Value

Customer Rated

Feb 03, 2015

Not a bad motor by any means, though slightly unrefined - which I put down toi the bearings. Very powerful on a 3S for sure: I used it (with a water cooling jacket) on an outrigger I built along with a 50A water-cooled ESC. Pushing a 35 mm 1.6 pitch prop in a static test I was able to get the ESC wires to smoke and the ESC to reduce power on overload but it was reliable and cool. Getting 75KPH on the outrigger.
3S is definitely the limit: pumping more volts just heats it up and the bearings start to rattle. Without cooling it heats very rapidly even on no-load so some type of cooler is required whatever the application IMO.

• Overall
• Quality
• Value

Customer Rated

Jan 23, 2015

Early days yet but it looks very promising. I am running it in HK wooden sponson race boat that I have modified with a Carbon/Kevlar skin and additional sponsons at the rear. The motor howls well running on a 3S. The only issue I had is the HK 28 sized motor cooler. BTW the motor itself was 28.03 AFTER chamfering the end of the can with some cunning to get the cooler past the O rings so be warned. After there is a mere 0.4mm of a gap around the periphery for water to flow around - to me this is compromise as it sets up too much back pressure and restricts flow through the ESC as well-=not a good idea. But this is the fault in the design of the cooler, not the motor.

• Overall
• Quality
• Value

Certified Buyer Rated

Mar 30, 2014

The spec and the product config table don't agree on the shaft size, but this motor does in fact have a 3.175mm shaft. A LOT of torque from this motor. I am running it in a tacon thriller.

• Overall
• Quality
• Value

Customer Rated

Jan 28, 2014

Great little motor. Have it in a Tacon Valor 1/14th scale monster truck and it is awesome. It's paired with the 45A Turnigy Trackstar ESC and both stay cool. It's hard to keep the truck on its tires and will do back-flips on command. Love it!

• Overall
• Quality
• Value

Certified Buyer Rated

Jan 21, 2014

Nice quality motor with plugs nicely attached as per the photo - I added a watercooling jacket for boat use and this motor doesn't dissapoint

• Overall
• Quality
• Value

Customer Rated

Dec 25, 2013

nsane power.
With hk 60a esc, 2x(3s 1.4a 80c)nanotech lipo.
On my mini e revo.
100 kmh, low tempature, on long run time.
Thanks hobbyking.

• Overall
• Quality
• Value

Customer Rated

Nov 21, 2013

i have this one in a radjet 800 on 3s 2200ma with a 60 a hobbyking esc and 4.5x4.5 propeller......very good speed. nice sound!

• Overall
• Quality
• Value

Customer Rated

Apr 30, 2013

Massive power, huge speed and great noise.
Used with 3S Lipo 2200maH and 60A esc. Great motor great speed.
Ordered two more to make 4wd offroading car designed by me.

• Overall
• Quality
• Value

Customer Rated

Mar 21, 2013

Most turnigy stuff is metric but this is all standard... 1/8th shaft. Odd. Replacement bearings are 1/8 by 3/8 by 5/32 deep. Turnigy bearings suck so I'll be replacing them with teflon sealed ceramic bearings. To get the back end off take out the 3 screws and tap the shaft end gently with a hammer. There is glue inside that sometimes bonds to the back of the case, many light taps are better than a hard one. I bought 4 and will likely buy more if they hold up to some abuse.