Registreren

Product Finder

Instellingen

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
Registreren
Shipped From:
  • USA

XK3665-2400KV borstelloze Inrunner

XK3665-2400KV borstelloze Inrunner

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Gewicht:
334 g
SKU:
XK3665-2400KV
Product
Omschrijving

XK3665-2400KV borstelloze Inrunner

Specs.
Max Amps: 80A
Max Volt: 14,8 V
Max Watts: 1185W
Rpm / V: 2400kv
Resistance: 0,0100 ohm
No-load Huidige: 3.4a
Afmetingen: 36mm x 65,0mm
Montagegat diepte: 4.5mm
Lengte van de uitbreiding van Shaft: 18.5mm
Shaft diameter: 5mm
Gewicht: 370g

Product
Specifications

Aanvullende Informatie

  • Sku:
    XK3665-2400KV
  • Brand:
    Nvt
  • Gewicht ( g)
    334.00
  • Lengte
    130.00
  • Breedte:
    50.00
  • Hoogte:
    78.00
  • Kv ( tpm / v )
    2400.00
  • Max Currents (A )
    80.00
  • Vermogen ( W):
    1185.00
  • Lengte B ( mm ):
    65.00
  • Kan Lengte D ( mm )
    63.00
  • Max Voltage ( V )
    15.00
  • Shaft A ( mm ):
    5.00
  • Unit Weight (g):
    308
  • C Diameter ( mm )
    36.00
  • Totale lengte E ( mm )
    80.00
  • Resistance ( mh ):
    11.00
Community
Discussions
Rate&
Review

Schrijf je eigen recensie

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
For the money its good value. I bought it as an experiment to see how it would perform in my Smash Shark mono-hull running on a 4S with a water cooling jacket, 120A ESC and spinning an Octura X440 3 blade prop. It lacked a little bit of bite compared to the Stock 3660 2075KV which I put down to a lack of low speed torque, bur once "out of the hole" its got a good top end but I havent noticed a marked increase in speed. I will now build it into a 800mm rigger I am building where the lack of punch isn't going to be an issue and that should allow it to reach around 80-90k's hopefully.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Great motor use it on my pursuit rc boat even fit the original cooling jacket no mods.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I've ran this motor several times and so far I have not met any problems to date.

I matched it with the 36mm cooling jacket that you can buy here in HK. With this combination, it's cheaper than buying a motor with built-in cooling jacket by at least $5 and works better in my opinion. This motor does not come with a female bullet connector for the ESC so just make sure that you have a 4mm bullet connector and matching heatshrink tube to seal it. In my opinion it's a good buy.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Love this motor have it in 2wd slash, race on track does great i will by again for sure... great motor
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Kfkfjfjfkfjfjfjfjgjfjjfjjfjfjfmfkfjfmfmf
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is an excellent choice for a brushless motor for any 1 8 scale car. Has a lot of torque and will make your car increase in will spins and wheelies. The reason why i gave four crowns for quality as the one mounting hole was slightly not in position meaning it need some mods for it to fit. overall excellent for its price and performance. keep up the good products HK and Turnigy.

Ayden.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This motor is 2 poles, construction as KDA inrunner but sectional, and a slightly better efficiency, but beware of contact between the cable and the rear facing the engine, there may be short circuit, it is good to analyze and implement control.I run in my 1:8 Truggy Caster with Turnigy cooler, the temperature is higher but in order.For the money a good buy.
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Productlabels

Gebruik spaties om verschillende labels te scheiden. Gebruik enkele aanhalingstekens (') voor zinnen.