Mostrar : TODAS AS CATEGORIAS 0 Aeronave 1942 Aviões 1104 Todos os Planos 147

70 milímetros EDF Jet Fighter - Fibra de vidro 620 milímetros (ARF)

70 milímetros EDF Jet Fighter - Fibra de vidro 620 milímetros (ARF)

7 Reveja

Preço:

Now save economize 0,00 € 0,00 €

77,18 €

Já comprado Discontinued Product

Please continue searching for a similar product.

SKU:

189000001

Envio Grátis? Clique aqui aprender mais!

Compartilhe este produto e ganhe 400 pontos (3,86 €) [ ? ]

Descrição do Produto

O Hobbyking 70 milímetros EDF jato certamente olha a parte e, como resultado da construção de qualidade, é um muito capaz jet modelo de alta velocidade. O jato foi projetado para ser um dogfighter e este modelo ostenta um tudo tailplane em movimento e boas aileron tamanho de dar o piloto RC o tipo de maneoverability que este lutador é famosa. Ala / construção elevador é espuma core / folha de balsa, a fuselagem, a ingestão, copa e facada verticais são composto, a tampa do ventilador é removível e uma folha de tubo eflux está incluído.

Este é um jato escala de alto desempenho acessível e prático que lhe dará muitas horas de diversão, uma unidade de ventoinha 70 milímetros incluído e o custo total de construção deve ser baixa para tal um bom modelo de qualidade. Parece ótimo, baixo custo de construção, construção de qualidade, grande insecto e, claro, desempenho balístico, o que mais você poderia pedir!

especificações:
Envergadura: 620 milímetros
Comprimento: 985 milímetros
Voar Peso: 1200g ~ 1350g
70 milímetros EDF

inclui:
unidade de 70 milímetros de alta velocidade EDF com 4 milímetros e 3,17 milímetros adaptador
Todos Hardware
Eflux Tubo
decalques
instruções

exige:
Sua própria 4 Channel TX / RX
4 x alta Torque MG Micro Servo
28 milímetros EDF Brushless Motor 3000kv Min
60A ESC
Bateria 2200mAh ~ 2650mAh 4s Lipoly

Especificações do produto

Vídeos

Envio vídeo

Registre-se para enviar vídeos, por favor assinar em ou registar

Discutir 0

Tópicos

Ordenar por

Tópicos Mais Recentes

Poste um Novo Tópico

Reveja

Registre-se para escrever comentários, por favor assinar em ou registar

DeltaDart | Comprador Verificado

Overall
Quality
Value

Customer Rated

Nov 20, 2013

This airplane is under-powered with a 4s set up. I installed an E-Flite 15 brushless motor with a Turnigy 4s 2650 mah, 14-blade EDF unit. Thrust output was well below anticipated thrust. I suspect the duct opening is too small and not enough air is getting to the motor. Bench check the motor set up and the thrust was incredible. Again, I suspect the duct inlet is too small. Anyone come up with a solution for more thrust?

Russell | Comprador Verificado

Overall
Quality
Value

Customer Rated

Oct 29, 2012

Well I got mine and the packaging was great. I too dint have instructions however did download the slides from the international file of this same plane. I have had it for a month and have it built. Do want to do retracts but the F-16 ones I have found put the retracts in the intake. It's to thin to do that. I'll figure something out. I. Like the plane and would recommend to someone with time and the skills to adapt the balsa for your needs.

slaanesh | Comprador Verificado

Overall
Quality
Value

Certified Buyer Rated

Sep 04, 2012

Nice kit. A few issues: 

A bit heavy. 

Needs a fair bit of build experience. 

Wing and elevator covering is good but it's painted and easily chips off. 

My setup: 

Change Sun 10-blade EDF 

Turnigy L2855 2300Kv motor on 5S 

Nanotech 2200mah 45C 3S and 3S in serial 

Turnigy 60A Plush ESC 

HobbyKing 939MG servos for elevators 

HobbyKing HXT-900 servos for ailerons 

COG 77mm from leading edge of wing where it joins fuselage. 

12mm elevator throws 25pcnt Expo 

5mm ailerons throws 25pcnt Expo 

Weight ready to fly 1320g 

Unflown. Maiden when the weather is favourable.

starefly | Comprador Verificado

Overall
Quality
Value

Customer Rated

Aug 04, 2012

It finally took the air after an unlucky first attempt during which I broke a wing. It has to be bungee launched with my setup to get a good elevator response on start.
Setup:
- EDF FAN 6904
- Motor: HET 2W20
- LiPo 3300mAh turnigy 30-40c
- 100Amps ESC
- CG 70mm at wing root
- Elevator 18mm travel
- Airleron 7mm travel

Behavior in flight is pretty good but need to be trimmed pitch up. Plane is fast and you easily lost him if you go too far away due to its small size....
First landings are a bit hard as the plane is coming fast but after few runs you are able to master beast ! :)
Nice little jet with good flying characteristics for the price, I will recommend !

CHRIS | Comprador Verificado

Overall
Quality
Value

Customer Rated

Jun 10, 2012

To make a long story short: I do not recommend Hobby King.
You will be better off supporting your local hobby shop where your SERVICE will be better and they will take care of you-unlike HK.
This purchase shall be the last -so savor the flavor HK -I am done.

CHRIS | Comprador Verificado

Overall
Quality
Value

Customer Rated

May 17, 2012

My order just arrived and the directions did not come with it. I specifically ordered it because the product description said it came with building directions...unlike some kits that do not.

Also, to add to my nice day (sarcasm) the plane came with a not-so-good packed airplane and one crushed right wing tip.

What a bummer...I will keep you all posted here on how HK handles this matter. I will not hesitate to tube this if i get burned.

Kyle | Comprador Verificado

Overall
Quality
Value

Customer Rated

Sep 14, 2011

Ok first off there are no directions. Alot of the assembly is up to you for example its not clear where the edf unit goes or how it mounts. Same with the servos, there doesnt seem to be spot for them. The canopy doesnt have any way to mount it that I can see. It comes with magnets but where do they go? No landing gear, you get what in the images and nothing more. It will be a fun project for some and something that never gets in the air for some others.

Manuais / Arquivos

Arquivos de clientes