Torne-se um fornecedor Blog Novos itens
Registar

Preço total

0,00 €

Carrinho de compras 0 Carrinho de compras 0 Loading...

8-9 polegadas Variável Setup Hélice de Passo w / conjunto de ligação e Monte

Generating Links

8-9 polegadas Variável Setup Hélice de Passo w / conjunto de ligação e Monte

Preço:

Now save economize 0,00 € 0,00 €

28,46 €
Já comprado Discontinued Product

Please continue searching for a similar product.
SKU:
095000048-0
Envio Grátis? Clique aqui aprender mais!

Hélice de passo variável 8 ~ 9 polegadas para aviões de espuma.
Para o máximo em desempenho de vôo 4D interior, não procure mais do que o sistema VPP 4D de Hobbyking, oferecendo trás vôo, rolamento vertical, paradas ar meados de e assim por diante. Esta unidade possui dois tamanhos de lâmina na caixa de 8 e 9 polegadas, montagens de fibra de carbono e acessórios de plástico rígido.
Esta é uma unidade leve dando flexibilidade para configurar em praticamente qualquer tipo de célula de espuma coberta. Você pode ter o servo para "VP" montou frente ou usando uma barra de pressão, tê-lo escondido fora da vista.

Uma unidade muito bom, arrumado e versátil, com nenhuma modificação do motor necessário.

Características:
• Montagem simples e fácil
• componentes de fibra de carbono

Spec:
Lâmina Tamanho: 8in (207 milímetros) 9in (233 milímetros)
VP faixa de ângulo: ± 15 °
Peso: 16 g
Servo: 5g-8g
Aplicável Tamanho do motor: 2204, 2206, 2208, 2212

  • Diâmetro X ( Inch) 8.00
  • Afastamento Y ( Inch) 0.00
  • Rotação CCW
attributeset-13
Close

Dimension Diagram Guide

  • attributeset-13

Close

Envio vídeo

Registre-se para enviar vídeos, por favor assinar em ou registar

Tópicos
Ordenar por
Tópicos Mais Recentes
* Nome de utilizador:

* Sua resposta:


Por favor, insira o texto mostrado na imagem no campo abaixo
*Código de verificação:
Cancelar
Submeter
Poste um Novo Tópico
* Nome de utilizador:

* Seu Tópico:



Por favor, insira o texto mostrado na imagem no campo abaixo
*Código de verificação:
Postar Tópico

Registre-se para escrever comentários, por favor assinar em ou registar

Billy Shaw | Comprador Verificado

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Nov 09, 2015

not the best, but works , make sure to take the time to tighten all the bolts and make sure to take time to set up the curves

JaRa5xxx | Comprador Verificado

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Dec 03, 2013

Nice system!

You can mount the servo directly on the supported CF mount or on the fuselage and control pitch with a pushrod.

I had to make one correction though: the recess in the prop hub that leads the propeller root was too narrow near the full positive pitch position, causing the hub to bind. I had to sand it a little so the hub could move freely over the full range.

Note that the hole for the propeller shaft in the hub is only 3mm, so you carefully need to widen it with a reamer or drill if you want to use a motor with a 3.14mm shaft. It would be great if HK could support a 3.14mm hub.

I recommend to use the innermost hole on the servo arm to control pitch. The range is then just sufficient for that and you want to use maximum servo force anyway. When I connected it to the 2nd hole of a TGY1440A, I couldn't get full negative pitch at high RPM. If the horn is too long, it may also flex under load, causing the control bearing to tilt and slow the propeller down.

Subir arquivo

Registre-se para fazer upload de arquivos.
Por favor assinar em ou registar para começar a ajudar amadores agora!