Registar

Product Finder

Definições

Useful links

Bate-papo ao vivo
 
[["US","AU","GB","DE"]]
Registar
Shipped From:
  • USA

EDF Ducted Fan Unit 5Blade 68 milímetros 2.68inch

EDF Ducted Fan Unit 5Blade 68 milímetros 2.68inch

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Peso:
80 g
SKU:
OR003-00105-5B
Descrição
do

EDF Ducted Fan Unit 5Blade 68 milímetros 2.68inch
Diâmetro da lâmina: 6 8mm / 2.68inch
Tipo Blade: 5
Tamanho do eixo: 3 mm
Feita a partir de alta resistência plástico reforçado.
Peças hélices disponíveis.
Motor recomendado: 28-47 9Turn (7,4 ~ 14.8v)
ESC: 40A
Rpm: 4,000kv
Potência: 750 ~ 950g Thrust
Este ventilador vai demorar até um motor de diâmetro 29 milímetros.


Product
Specifications

Características do Produto

  • SKU:
    OR003-00105-5B
  • Brand:
    N/D
  • Peso ( g )
    80.00
  • Comprimento
    95.00
  • Largura:
    90.00
  • Altura:
    90.00
Community
Discussions
Rate&
Review

Escreva a sua análise

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
This edf is practically unusable because of the shaft adapter. There are only 2 grub screws connecting the adapter to the motor shaft, and they are at opposite sides of each other. Thus, one axis is solidly connected, while the other has quite a bit of play. I can't believe a fan of this small size does not have a simple collet. In addition, the fan blades barely fit into the shroud, and with the adapter imbalance, the fan rubs agains the inside of the shroud. Also , the nose piece has the hole drilled almost 2 mm off center. I should have paid more attention to these negative reviews, because this was a waste of money. Btw this product was purchased sometime in july 2014. Hope this helps.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Hey guys, I just did a quick set up on mine. First off for the money, greeeeaat fan. The bad is you have to check blade lengths . Blades are not cut to same length. Outer housing is a little flimsy, but I believe once it is in the frame and surounded by GORILLA EXPANDING GLUE, it wont vibrate and touch blades anymore.So the bads are easy fixes. I am big on High KV motors and 2 cell lipos for high thrust and light weight setups. My motor is the Turnigy 4400 KV 450 heli motor.ESC is Turnigy 55 Amp Trust. 2 Cell Turnigy Nano Tech 35- 70 C discharge lipo ( these are a must for high KV motors). I will keep you posted on thrust numbers, but on 2 cell it is a beast. Pulls hard maybe about 600 - 800 grams thrust. Quality could be better, but you cannot beat the greeeeaaat price and overall quality. I am very happy with it, highly recommend. Hope this helps.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Buyers take note, the shaft adapter included with this fan is NOT for a 3mm shaft - it fits a 3.17mm (1/8 inch) shaft - it is very loose on a 3mm motor shaft. The rotor requires quite a bit of tidying up - the blades have quite a bit of flash on them. Having said that, I think it is still a good value fan.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Just about get a 28mm outrunner in there, maybe .5mm spare to the outside of the can. techtip, roll some strips of card around the can of the motor to centre it in the mount till you cant get anymore in.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I bought 2 of these. One was SEVERELY out of balance and despite my efforts, it still is...the other one however was pretty balanced. i sanded parts of the shroud so that the rotor would SPIN without touching shroud....and now...I spooled up one of them and MWAH....ITS A BEAUTY!! I am running them off 2S and they seem to give quite some thrust...however...i havent measured it. Great buy...just be sure to balance them.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
the motor diameter may not exceed 9"/8, it should be 1" to allow some clearance. I don't see how it is supposed to be cooled unless it has fins on the end, starting at 1" from the mounting plate.
The motor needs to have 2 or 4 screw holes on the shaft side that are on a diameter between 5"/8 to 7"/8.
Unless the motor has a shaft extension it takes an in-runner.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I bought 2 of these. with the first one, the rotor wouldn't fit and spin freely in the shroud, so I trimmed the blades and now its badly out of balance, adding the Impeller makes it worse. I was about to trim the second one but then, checked the rotor for balance and it was in balance, so I just sanded the shroud and made the rotor fit.

First EDF....Thanks HobbyKing

I'll be making reviews at RCgroups.com (Username: hamdhan)
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Adapter is 3mm as stated but a slightly loose fit on my brushless motor which has a 3mm shaft.
Rotor is off-center. That mean that it has a wobble which was very clear on my Du-Bro balancer. Topic on RCGroups.
Date of review:25/7/11
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Running with HXT 2835 3900kv Brushless Inrunner. Produced 600g with 2200mha lipo at 24-26 amp. Great value.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
this is the best edf $/rpm if you balance it it's a gret edf
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!

Etiquetas de Produtos

Utilize um espaço para separar as etiquetas. Utilize aspas simples (') para frases.