Aé uma plataforma atraente e concebido de forma soberba com aa série de características puras que fazem deste modelo um dos melhores em sua classe.
Para resistência e fiabilidade, o modelo apresenta uma fuselagem moldada golpe que utiliza Nylon e é praticamente indestrutível, as superfícies de vôo são todos feitos de espumadifícil. Do ponto de vista prático, as asas são plug-in eo modelo requer não cola para a montagem. Tudo simplesmente parafusos juntos. O dossel exterior é puramente para olhares e é usado quando a é hasteada como um planador, embora unclips em segundos para revelar uma plataforma pronta câmera, completo com um furo de montagem de pan / tilt servo que tenha sido pré-moldado. Esta tampa da câmera de plataforma / asa grande é garantido por uma trava de liberação rápida e uma vez removido, revela enorme área de copa para a montagem de baterias e equipamentos sobre uma placa de contraplacado pré-montados. Todos os servos, motor e são, naturalmente, pré-instalado.
A asa de duas peças tem molduras para adicionar abas se desejado, mais moldado C de indicadores G na parte de baixo para verificações pré-vôo rápido. Não há dúvida de que este é um design soberbo, modeloalta qualidade a um preço excelente. Seria justo dizer que é mais atraente para olhar do que a maioria das plataformas para não mencionar muito mais difícil, a dará as horas RC Piloto de diversão para muitos anos para vir!
• Plug and Fly - Basta adicionar a sua escolha de bateria, o transmissor eo receptor
• Moldado asas e moldado por sopro fuselagem de plástico
• compartimento fuselagem dianteira Espaçoso
• Canopy / escotilha tem base plana para a montagem da câmera FPV
• desempenho de vôo estável
• abas opcionais
• Plataforma plana montagem popa da asa para montar a antena FPV
Envergadura: 1600 milímetros
Comprimento: 1.044 milímetros
Voar Peso: 950g
Motor: 2812 1400KV
Servo: 4 x 9g
4 ~ 5 transmissor e receptor CH
3S 11.1V 1800 ~ 2200mAh bateria lipoly
Características do Produto
Peso ( g )
love this place. solid construction and decent glide capabilities, haven't had it long but so far it's outstanding i did swap out the motor and speedy as well as aileron servo's and elevator servo. and used them for flaps while using mg servo's all round, only because of the distance i want to do with this i dont want any failures.
all in all on the build i'd tell everyone to go buy one.!!!
love it!!!The electronics are crap so I replaced the lot.
The plane itself isnt too bad but and its a big but...
The motor mount and pod are awful.
They are both soft and brittle.
I have ordered the V2 mount from Hobbyking in the hope that I will at last have a good fpv platform.
In the end this has cost me nearly double the buying price to get it working well.
The FPV raptor 1.6 is the best fpv plane i have had. Its rugged and has loads of carrying capacity. Just replace the electronics. They really need to supply a kit version.This is great aircraft. The only thing that lets this aircraft down are the wing bolts, it would be more convenient if it had some type to thumb screws or quick release system.
Has good pay load capacity, and EPO foam is good quality.
Packaging could be better to protect the aircraft, mine had damaged on vertical stabiliser, but nothing a quick soaking in boiling water couldnt straighten out.
The decals I received where like 100 years old, all curled up and they dont stick. Hinges also need some reinforcement but those minor complaints aside, quality wise it seems fine, and a fairly easy build. There is LOTS of room in the fuselage, I shouldnt have problems mounting a flight controller, GPS, OSD, and amp sensor.
I flew the maiden with a 2200mAH battery and no fpv gear besides a mobius in the cockpit. Its borderline tail heavy even in that configuration, pitch stability was bad, didnt fly nicely. Forget about even smaller batteries, with a 2700 and 3300 it balances out and becomes a much nicer plane to fly, however, it also becomes even more underpowered than it was. Its OK for FPV and learning how to fly, but the power just isnt there to get you out of trouble, and even doing a looping from level flight is nearly impossible without diving for speed first.
Lack of power makes take off also a bit of a challenge, it needs a healty throw. Although I did manage to take off from the snow with no problems. Maybe it will work on (wet) grass too.
Power aside, flight characteristics are very good. Glide angle is excellent and I suspect flight times will be impressive (didnt time my flights, and it was freezing cold, but I suspect 20 minutes will be a given). She is pretty forgiving when stalled (if cg is correct), rolls nicely, doesnt 'auto level' like a bixler, but i<a href='http://www.hobbyking.com/hobbycity/store/uploads/684449117X991778X39.JPG' target=_blank>Igor</a>
http://youtu.be/Jksawf6IYucPurchased for my first FPV flying experience and flew well but felt a little under powered. Replaced all my servos for metal geared and fitted 40A ESC and a NTM 28mm 1400kv motor......perfect.
I went a step further and swapped out the wings for 2m Phoenix 2000 wings with minor alterations. Maidened it today and what a great plane for FPV gliding about was perfect. Needs a fair bit of weight in the nose and 2 x 2200mAh 3S batteries are perfect. As it doesn't use much power flight times are great too. HIGHLY RECOMMENDED.....May be a little under powered but this plane can take a beating. Went into a nose dive close to the ground and hit with a load bang. Picked it up and brushed off the dirt to find a little gouge in the nose. I replaced the battery and check the flight controls and I was flying in 5 mins.I can't really recommend this one because it requires so much upgrading to make it good. Mine arrived with 2 dead servos so I replaced most of them. The body is hard plastic, which is nice, but it's also heavy meaning that if you're going to put in a big battery and FPV gear then you also need to upgrade the motor. With stock motor it's ok but slightly underpowered and definitely will NOT take off from the ground as advertised, even with a 2200 in there. I ended up upgrading the motor to a Rimfire .10, which now allows it to take off from the ground and gain altitude reasonably quickly. Of course this also required a new ESC. You can see where this is going... It's now a much more expensive model.Received it the other day double boxed which was good as outer box damaged,Hole in the side inner box was all good, on open the box wings wrapped in bubble wrap no damage, fuselage is bigger than expected blow moulded plastic as is the Phoenix. All bits and pieces are as they should be seems as though there are lots of spare screws 2 spare clevises and there was safety clevises rubber bands. Motor pod fits well and 4 screws to secure and is as described and esc, rudder and elevator fit in plastic clamp which clamps through tail section 2 screws for elevator and 2 screws for rudder all fit good, now for the bonus if you have a Phoenix the wing are exactly the same so the 2 meter wings fit and if you have the 2000 Phoenix you know have the 1600 Phoenix as these wings fit. All in all happy with purchase and HK service. Maiden flight to follow.