O FrSky Lipo Sensor Voltage apresenta um fácil de ler visor colorido, OLED. Ele pode ser usado como uma unidade única para o controlo da tensão das suas células LiPoly, ou pode ser usado em conjunto com o sistema de exibição de telemetria FrSky DHT-L como um sensor de complemento para monitorar a sua bateria.
O cabo do sensor (para utilização com L-DHT) está incluído.
Peso: 5,2 g
Faixa de medição: 1 ~ 6S lipoly
Faixa de exibição voltagem da célula: 0.20 ~ 4.20V
Resolução de tela de tensão: 0.01V
Precisão de detecção de tensão: 0.05V
Atual do conselho: 15.5mA
Faixa de temperatura operacional: -30 ° C ~ 70 ° C
Pixel: 128x64 com tela de OLED
Características do Produto
Capacidade ( mAh)
Peso ( g )
works great and very handy. a great addition to my taranisProduct defective, dont work, arrive now and trash.... Dont buy this...
Produto com defeito nao funciona, lixo! Nao compre...CHECK THE DISCUSSIONS BEFORE YOU PURCHASE.
It lasted me all of a couple minutes. Now it only shows a 2s no matter if I connect a 3s or 4s.
I'd wait till they get this thing debugged. There has been quite a few failures. Mine included.
When it worked it was cool. The output worked great for my telemetry and was able to read it on my transmitter. I would have given it 5 crowns.accurate and light ,all goodCute tiny sweet sensor with super nice OLED display, bright and perfectly readable even on bright sun, wok even standalone, wonderful. Definitely my favorite FrSky telemetry sensor!
This I would said last week, until it started to show too low error voltages on two cells (2 & 3) and finally cell 3 disappeared definitely. Fully charged 3 cell battery read as 2 cell with one almost dead cell on 1,3V. I disassembled it and found out, that few resistors on input voltage dividers are dead, some damaged, don't know why and how. I desoldered 2 highest ones (from cells 5 & 6) and replaced 2nd and 3rd and now I have FLVS only for 3 cell accu, but working again. That was smallest smd resistors I have ever seen, damned little bit**es. By the way, they are 100k value. I have placed pictures of naked FLVS and thoose resistors to files section.senzor napeti pro frsky telemetriiVery poor QC, the sensor only shows one cell voltage every time, no matter how many cells have your battery, tell me very bad about the QC of FrSky products, may I trust in the transmiter module or in the receiver?, that pieces are much more important that this sensor, if they fail, you can get injured somebody or damage the private property, HK you must do something with this issue.All voltages on my display, thats what I wanted and thats what I have now. Godd resolution and seems to be accurate so far, so I recommend this.I am afraid that mine was DOA!
On a well ballanced 3S mine reads 3.76, 2.58, 4.20 !
I have measured the cells at 3.77, 3.74, 3.74. Measured with a lab quality 6.5 digit agilent 34410A Multimeter.
Not much use so in the bin it goes!It's really bright, and accurate to 0.01 volt! It can also be use on my FrSky Telemetry system.
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
FLVS_naked download now [786kb] FLVS_naked2 download now [713kb] Replaced_little_bit**es_in_centimeters download now [428kb] X8R - Vario - FAS - FLVS download now [710kb]