Estes motores shockie pequenos soberbas oferecer excelente desempenho e grande valor para o dinheiro. ferida mão e equilibradas estes motores super leve são fantásticas para o mais leve dos modelos internos de luz em seu perfil 3D e F3P. Equipado com ouro 2 milímetros banhado plugues de bala e um motor de fibra de carbono super leve monta estes motores estão prontos para parafuso no e decolar!
design de peso leve.
montagem forte e CF luz motor.
Pré-instalada conectores de ouro de 2 mm.
Construído em proteção de prop.
RPM / kv: 2100
Ociosa atual: 1.5A
LiPoly: 2 ~ 3s
Max atual: 10.9A
Prop sugerida: 9x5
Tamanho do eixo: 3mm
Peso: 19,6 g (peso verdadeiro incluindo fios e conectores)
Dimensões de montagem: 35mm x 35 milímetros
3 x 2 milímetros conector fêmea
2 bandas de poupança x Prop
1 x CF Motor mount
3 x Pré-cut encolher tubos
Características do Produto
Peso ( g )
Kv ( rpm / v )
Correntes Max (A)
Comprimento B (mm):
Pode Comprimento D (mm)
Max Tensão ( V)
Shaft A ( mm):
Unit Weight (g):
Diâmetro C ( mm )
Comprimento Total E ( mm)
Resistência (MH ):
I intended to use this with a e-flite nieuport. connected to zippy 800mah 2s 20c and a plush 10a esc. Startup up was jerky and abrubt. Tried a HK red brick 10a still same problem. Same with HK 8/10amp. Replaced motor with turnigy park flyer 250 of 2200kv. Big difference. Nice and silky smooth with plenty of power with all three of my tested esc's. Although it looks pretty and appears well made I still can't recommend this red HK motor.Super moteur tres bien conditionn avec les accessoiresTried a 8x4 gws on 3 cell .....15 amps and hot motor. Had to go down to a 6x 3 prop on 3 cell and it would rip the little prop had to really stay on the throttle. Finally tried a 8x4 on a 2 cell and good performance I think it was at 10 amps. Next time out I will try a 9x4.7 on the 2 cell and see what I get. I would buy another one for a crack yak or 7 oz or less airframe with the 8x4 prop. It would be super on a 6oz plane.Very compact and lightweight. I used this motor in a pusher configuration powered by a Turnigy 3S 800mAh 35-45C battery through a Turnigy Plush 12Amp ESC, spinning an orange GWS 8x4.3 prop.
It has great responsive power! But don't expect the motor to last if you don't manage your throttle usage appropriately.
In hindsight, I may have been able to avoid burning up two of these already by evaluating my setup with a watt meter first.Using this in my 3d profile scratch build. Great little motor and very strong built.It took me a while to figure out the slowfly APC prop is the best. The GWS 8x4 was my first choice, but the hub on the motor is too small. I had to use the busing that came with the 8x4.7 slow fly apc prop and then after insertion, drill it out. Now the hub sits on the motor very well and with a tight O-ring, the balance is amazing. The trust is great and the motor flys warm on 2S as I 3D fly a 290 gram biplane from TechOne. I don't recommend any prop larger than the 8x4.7 as it will heat up the motor instantly. Super light and powerful, just be sure you get a tight prop fitting.Good Motor ...........................................................................................................................................Gewicht 19,27g inkl. Kabel(5cm)und 2mm Goldkontaktstecker
Prop-mitnehmer etwas lockerer Sitz fuer GWS (zB.7x6)
28 Statoren - besonders ruhiger Lauf, sehr hochwertige, sehr leichte Ausfuehrung ideal fuer 150-200g SchockflyerJust got one, very well machined, weight is true, relatively clean windings.
Didn't measure thrust yet but feels good!
I plan to use it with a techone spirit, keep you updated...
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!