As aparências enganam. Este outrunner é cerca de duas vezes o tamanho de um motor TowerPro sino, e balança um suporte muito maior. Seu motor usado em alguns de Arte-techs novos kits de avião, que é testiment à sua durabilidade, facilidade de uso e qualidade.
O DT700 vai balançar um 11x4.7 SF prop bem, para produzir mais de 900g de empuxo.
Seu grande para foamies maiores GWS ou aviões parkfly.
Voltagem necessária: 11.1v
Sugeriu Capacidade da bateria: 1300mAh +
Sugeriu Prop: 10x4.7, 11x3.8 ou 11x4.7
Max consumo de corrente: 13A (com prop 11x4.7)
Max impulso: 900g +
Sem carga atual: 1.2A
Shaft: 4M (perfeitamente adequado para Towerpor / GWS SF adereços Fly Lento)
Diâmetro: 41 milímetros
Comprimento total: 77 milímetros
Kv: 700rpm / v
Vem com montagem, como mostrado na imagem
Relatório de teste.
Nós usamos este outrunner para alimentar a um e-tech Pitts. Corra com um pacote de 1300mAh 3S1P 20C, 18A e BESC 1147 GWS / TowerPro prop, os pitts Art-tech correu bem. Excelente taxa de subida, embora não hoverable, e com tempos de voo 13minute ou mais, ficamos muito impressionados.
A outrunner muito eficiente para os modelos de vôo mais lentas de até 0,15 tamanho.
Características do Produto
Peso ( g )
Kv ( rpm / v )
Correntes Max (A)
Comprimento B (mm):
Pode Comprimento D (mm)
Max Tensão ( V)
Shaft A ( mm):
Unit Weight (g):
Diâmetro C ( mm )
Comprimento Total E ( mm)
Resistência (MH ):
very powerful bell motor, i ts almost equal in performance with a 35xx motor 920k, except that its half the price , also it can handle 4s easily, if 10-12`prop-=25amb esc
if 13 prop= 30 a escUsing this motor with a 30 Amp car ESC for an ROV project. So far preliminary tests are working nicely. It produces quite amount of thrust with my 57mm boat props, while submerged. the only problem I've had is that the set screws in the base seem to strip fairly easily, and I've had to drill an indent to keep the control wires from coming loos and flopping around.It's a good product. It works as it should be.
Two thumbs up. I would like to recommend it to all user.cheap work well and very efficient. the one and only down side is I have had 2 out of 4 have magnets come loose. I hope hk can in prove on their quality of products.These motors are ok for scratchbuild multirotors, but you will soon find they are a bit sluggish. You need to epoxy the wires which I am sure has been stated, but I ruined two motors before I did it correctly. I used Amazing Goop for ease. I have these on an h-quad, but they make a lot of vibration. I think all bells have that as they have such a small support, but large bell. For the price I'm sure you can find better motors that spin freely and have no need for modification.Good motors ....for the price....the issue is you can't really tighten props as if you try to screw the props too tight the shaft has a tendency to slip and cause the end ring clip to push against the bottom bearing causing the motor to run like its a bit jammed...gummy feel...I would go for the zip tie method to mount props....better bearings would be great....and neater windings would make this a killer deal....I don't think patrons would mind paying a couple of dollars more for this...all in all it is a great motor for a cheap not so trusty multicopterSuperb item to use in all RC stuff. Just safe peace of mind that you have a tad better item in your gear. Buy with confidencegood motor, altough winding is not the best quality.
If you crash your plane and shaft bends, there is no replacement parts for it.best brushless motors for my projects period, I have too many of them now.I have four of these DT700 motors and have used them on a tricopter preceding the quadcopter. I used these with the 11x4.7 sf props. They are good motors for the money but are a bad long term investment. They do what you want in the short run but if you are looking to go out and fly a multicopter and not worry about having a motor bearing go bad or the set screw loosen during flight or the balance being off, I would advise not to buy these motors.
If your going to build a multicopter, buy durable long lasting motors that will keep you on the flying field instead of in the workshop. Buy a quality set of motors. quality motors will most likely cost around $20-$30 per motor, especially if your using looking to get aerial footage and have a lot of expensive equipment on your multicopter. This may seem steep and I'm sure people will attest that their DT700 or DT750's work great, and good for them, but your going to spend the money either on a replacement or on bearings which will total to about the ammount of quality motors.
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
better_way_for_screws download now [30kb] DT700 on homebuilt Karbon-X Frame download now [278kb] DT700 on homebuilt Karbon-X Frame download now [287kb] Custom motor mount download now [126kb] No File Name download now [48kb] Winding1 download now [847kb] Winding2 download now [754kb] Winding3 download now [772kb] Measurement with 1245SF prop download now [11kb] DT700 vs L2210-1650 data set download now [24kb] DT700 vs L2210-1650 data set download now [24kb] No File Name download now [74kb] No File Name download now [48kb] DT700 ROV thruster 4.19 lbs 5A download now [512.70Kb]