Registar

Product Finder

Definições

Useful links

Bate-papo ao vivo
 
[["US","AU","GB","DE"]]
Registar

Módulo de Alimentação HKPilot com T-conectores e 6 Pin 150 milímetros Cabo

Módulo de Alimentação HKPilot com T-conectores e 6 Pin 150 milímetros Cabo

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Peso:
42 g
SKU:
9387000031-0

Combine

essential items and
acc
Descrição
do

O módulo de alimentação HKPilot 2.5 incorpora tanto uma forma de alimentar o seu HKPilot e acessórios e relatar voltagem da bateria e corrente para o HKPilot, isso pode ser visto em toras estocadas do HKPilot ou viver com um rádio telemetria. Tudo através de um único cabo e firmemente incluída 6 pinos que corresponde diretamente o conector do HKPilot. As saídas do regulador de comutação 5.3V on-board em um máximo de 2.25A, e pode ser usado até 18 Volts (4S lipo) ea um máximo de 90 amperes. O módulo de alimentação está pronto para usar com T-conectores pré-montados, e encolher embrulhado para proteção.

Nota: O módulo de alimentação é avaliado em 2,25 Amps para alimentar o HKPilot, receptor e periféricos (GPS e rádio telemetria) SOMENTE. Para poder servos usar um ESC com um BEC adequada ou um autônomo BEC conectado ao barramento de saída e remova jumper de 1 para isolar as duas linhas de energia.

Especificações:
Max tensão de entrada: 18V
Max sensor de corrente: 90A
Saídas de comutação regulador: 5.3V na 2.25A max
6-pos cabo Molex conecta diretamente para HKPilot
Medição de tensão e corrente configurado para 5V ADC

inclui:
DF13 6 posição do conector 150 mm de comprimento
Módulo de Alimentação HKPilot com T-conectores

Product
Specifications

Características do Produto

  • SKU:
    9387000031-0
  • Brand:
    Não
  • Peso ( g )
    42.00
  • Comprimento
    100.00
  • Largura:
    15.00
  • Altura:
    40.00
Community
Discussions
Rate&
Review

Escreva a sua análise

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
While the 5v output of this module should be 5.25v, this module is actually outputting 5.50v. The pixhawk/hkpilot board detects this overvoltage condition and faults the board.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Soldering quality is disgusting! If you're planning to use the cables/ T connectors, do yourself and your craft a favor by re-soldering them.

On the positive side, it works beautifully and the DC-DC converter piggyback board is of great quality.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Works as advertised.
I replaced the input T connector with XT60 and soldered directly to the PDB the output wires. Nice thick 12awg wires.
For Arducopter I had set a value of 17Amps/volt but I think 12-13A/v should be better.
The 5V SBEC was kinda in my way, trying to fit it inside a Trifecta frame, where the PDB is, so I removed it, connected it with wires (looks like only 4 out of 5 pins are used) and placed the regulator somewhere else.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I am using this on the HKAPM micro, with slight modification to the cord. It worked right out of the box, with minimal setup through the Mission Planner software.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
BE CAREFUL and check this Power Module before installing. I installed without checking and immediately smoked it. After the smoke cleared I found the positive (Red) and negative (Black) leads on the output side were reversed. The Red lead was actually negative and the Black lead was positive. The input side was wired correctly.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Cosa posso dire e un power module
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
WRONG CABLE!!!!! the cable you see in the picture and actually shipped with the kit, does not fit the hkpilot board connector...... you can tell me what to do ????
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I had to get the one with T connectors ...So a bit of soldering for me .

BUT

EVERYONE SHOULD DOUBLE CHECK THE SOLDERING ON THESE AND Really TAKE 5 MINS TO REDO THEM .

Otherwise perfect Item cannot miss the amp/volt readings any more
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Get this one if you don't want hassel of powering up the board and you get the voltage data for FPV as a bonus!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
bought this to go with the HK apm board which was working fine for more than a week. when this module arrived I plugged it in and at first all was OK but after about 10 connections the module failed with low volts out the sbec and took out the APM with it so I now have $100 of scrap electronics. In fairness to HK the sbec was a sub component made by a reputable US company.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!

Customer files
Pin layout download now [170kb]

Combine

essential items and
acc

Etiquetas de Produtos

Utilize um espaço para separar as etiquetas. Utilize aspas simples (') para frases.