micro motores de alta qualidade. precisão ferida com fio de prata-cobre e lâminas ultra-hard-prima.
desempenho extremo e eficiência para o seu micro avião.
Kv: 3000rpm / v
Lipo Intervalo: 1 ~ 2S (3,7 ~ 7.4V)
prop sugerido: 5030
Max atual: 3A
Explosão atual (5 seg): 4A
Peso: 5,4 g (incluindo montagem e arame)
Shaft: 1,5 milímetros
comprimento do eixo: 14 milímetros
Dimensões: 14 x 13 milímetros
Dados de teste:
5030 prop (recomendado)
Por avião 70g 3D e vôo normal 120g.
Características do Produto
Peso ( g )
Kv ( rpm / v )
Correntes Max (A)
Comprimento B (mm):
Pode Comprimento D (mm)
Max Tensão ( V)
Shaft A ( mm):
Unit Weight (g):
Diâmetro C ( mm )
Comprimento Total E ( mm)
Resistência (MH ):
??????? ????? ?????????, ? ??????? ????? ??????, ??????? ?? ??????.Works great with a handlaunch glider conversion..Used this engine as a replacement for the original gearbox and engine for a SU26XP from Parkzone. Power is roughly the same or somewhat greater. Used together with the 0,7gr BL controller from Hobbyking. Great!! (included a propsaver - 4mm)My P51 Mustang, Dave Rovelen plans, 46 cm wing span, 70 g AUW. GWS EP-4530 prop. Lipo 2S180 mAh nanotech flew like a rocket with this motor half throttle.I swapped this motor into my UM T-28, and wow this thing is fast! Check out the Ultra Micro T-28 thread on RCgroups if you want to see pictures. I used the Plush 6 amp, MAKE SURE YOU INSTALL A 1 amp diode (like 1N4001) between positive line into the brick or you can fry it. Then swap it to brushless and POW! You've got a much faster bird. Heavier too, so it handles a little more wind. Only draw back is that it doesn't "float" as much as it did before.I used this for my Ultra micro T-28. converted to 2s brushless setup using this motor, TURNIGY Plush 6A /.8bec/6g Speed Controller, and even a slightly large 300mAh nanotech battery. weight including battery was 65.5g, and this setup allows me to pull straight up. I would say to put the throws down slightly since the plane is at least twice as fast now! here's the thread with the info.
http://www.rcgroups.com/forums/showthread.php?t=1282886&page=563Very good quality for a very powerful motor.
I use it on a 100 g slowflyer plane and it works well.
I think this motor can trust up to 150 g slowflyer planefinally install it in my home built depron patern 3D plane AUW 70g on 2s 180 mah 4.5X4 prop have a good power and speed, little noisy at full power but all and all very happy with it, will get some more for the next project.HIGHLY RECOMMENDED installed in my 2s converted PZ Sukhoi XP micro, with a 5x43 prop and it HAULS. Faster than a newer UMX Sbach! The only reason for quality 4 stars is because the wires are soooooo tiny and brittle, had to hot glue on the solder points on the ESC to prevent them from breaking with vibrations.Outstanding little motor, combined this with a 5A 1S Brushless Controller, GWS 5x3 prop on a 75g depron wing and it's very fast
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!