HobbyKing FPV250 Santo Edição LED Night Flyer FPV Drone

• Overall
• Quality
• Value

Certified Buyer Rated

May 24, 2016

easy to assemble, i use 1806 2300kv dys motors with 12 amp esc's and it flies well.

• Overall
• Quality
• Value

Customer Rated

Jul 17, 2015

Finished already two of these amazing nightflyers.
The first one has 1806-2280kv motors, 5030 translucent propellers, 10A flycolor escs, kk2.1.5 board and Turnigy 5-channel receiver. With 1500mah/3s I have about 15 minutes flight time. The settings are: roll and pitch 30-100-20-30, yaw 100-90-30-25,
self level 50-20-40-40.
The second one has 2205/50 1040kv motors, 20A escs, 6045 propellers 3-blade, and
jiyi p2 flight controller with GPS. Flight-time with 4000mah/3s Multistar around 18 minutes.
PS: Don`t forget to learn the escs. I did it very easy with Turnigy servotester setting to Auto which continuously cycles the servo limit to limit.

• Overall
• Quality
• Value

Certified Buyer Rated

Jun 13, 2015

Added this to my order for fun. Now its assembled and I've added a long frame kit with some spare 1806 motors for fun. Its looks like a cheap toy, but its better than leaving my spare gear to collect dust.

• Overall
• Quality
• Value

Certified Buyer Rated

Jun 10, 2015

nice cheap framer for a starter project, LEDs make it a fun night flyer and the PDB is very handy. Excellent buy when it was on sale for 6AUD. Just note that the motor mounts are too wide for 1806 motors, as their screws are too thin. As a result, might look into buying a set of 22xx motors to fit onto this frame

• Overall
• Quality
• Value

Customer Rated

May 16, 2015

After few different setups finally got it working: 12amp afro speed controller , turnigy 1806 2280kv , naze32 flight controller , 1300mah 25c 3s . NICE little thing to try some acrobatics . I don't like the green-red combination of lights( I'll change the LEDs to red-blue ). The top cage is to small to get the flight controller and will need some mods.Looks really messy in the end with all the cables but flies great. For FPV I use a tarot 250 frame , so this one stays for night flight.

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 01, 2015

Looks absolutely beautiful in air in the night. stunning looks and features it even has a pan and tilt servo mount for the FPV cam.

• Overall
• Quality
• Value

Customer Rated

Jan 03, 2015

The workhorse of my FPV fleet is my FPV-250 V2, the long frame Diatone kit. Because I had the Turnigy RGB LED kit, some standard red LED strips, and a BEC to power them all, making the little quad visible for night flying also meant it was heavy. An 1800mah 3S would give me 6 minutes, with FPV gear and Mobius, running 2204 2300KV motors from RTFQ. After upgrading to this frame however, and low-slinging my cage, not only is my quad 100 grams lighter, (560g with battery), I'm getting significantly longer flight times hitting the 8-9 minute range. Visible even in bright Florida sun, these upward facing LEDs do quite a job lighting the frame, allowing LOS orientation out as far as direct LED lighting would allow. The best part of this though, in my opinion, is the distribution board with BEC, those little white LEDs give my low-slug a internal glow that is awesome!

• Overall
• Quality
• Value

Certified Buyer Rated

Dec 23, 2014

nice frame fpv 250 or some acrobatics in night time

• Overall
• Quality
• Value

Certified Buyer Rated

Dec 22, 2014

Excellent chassis.Facile construire.

Tout est fourni y compris les petites visseries.

Les LED avec un accu LIPO 3S sont trs belles

• Overall
• Quality
• Value

Certified Buyer Rated

Dec 19, 2014

Insane in the main frame (or so).