Controlado por um micro controlador baseado Atmel Mega168PA 8-Bit RISC e utilizando um único MEMS 3 eixos giroscópio o i86 Multi-Rotor Control Board Hobbyking é capaz de 8 tipos de artesanato Multi-rotor e 2 modos de vôo, sem a necessidade de piscar o micro controlador . Os sistemas de interruptores DIP simples permite a seleção rápida e fácil de seu modo de configuração Multi-rotor e vôo desejado.
Leve e compacto, o i86 pode caber no menor dos artesanato e inclui um pequeno pedaço de fita dupla face para instalar.
O i86 Hobbyking Multi-Rotor Control Board suporta:
Aero (asa fixa)
Todos os modos acima pode ser definido no modo "Normal" ou "Sports" mode (padrão normal)
Tensão de entrada: 4V para 6V
Sinal de entrada: 50Hz PPM padrão
PWM Frequency: 400Hz para ESC, 50hz para servos
escala Gyro: 500dps +/-, ODR: 800Hz
Temperatura de operação: -40 ° C a 85 ° C
Tamanho: 40 milímetros x 40 milímetros
Características do Produto
Peso ( g )
great price too took only a few minutes to set up
highly recommend this
board really good for filming with pots around 75pcnt
not so great for acro unless update firmware which is easily done with a usb asp i brought 2 !Works well ! Quick and easy setup, good price!Couldn't get it to work properly, even though, i did everything manual said. It starts shaking before you take off the ground. Maybe I didn't have enough experience with gain adjustment, but this was how I crashed my first quad...
I used it in st360 with multistar 20A ESCs and corona receiver.
Everything apart from shaking seems to be okCan't quite believe I missed this important bug when disarming. I nearly got a 11" prop at full speed in the eye and it has ruined my 3 DT750 motors.
Please do not be complacent like I was, this board has not been fixed since all the bad reports regarding the disarm bug. DO NOT USE IT FOR MULTIROTORs. I don't care that it only seems to do it for SimonK ESCs, this is just not acceptable safe programming of a flight controller. I will be asking for my money back and money for the 3 DT750s. Sorry HK, you simply are playing with fire by selling these boards.Couldn't make my Y-6 fly stable with it - was almost uncontrollable with whatever tune-ups I've tried. Replaced with KK2.1 and on the 1st flight copter hovered in the middle of the room with my hands down. There are much better boards now than this one.awesome controller , very flexible , easy to setup with dip switches , very stable
a good place to start in quadcopters
really chesp a great alternative to the kk board
a great budget board once set up. mine was a bit tricky as it turned out the motor diagram was wrong. motor 2 should be motor 1, 3 = 2, 4 = 3, 1 = 4, once that was sorted it all worked fine, only rudder needed reversing on the tranny, so for the maiden, stable in the hover, just a slight drift to the right. I can correct that with a bit of sub trim. so a great budget board to start flying multi rotor machinesI got two of these for a project quad. Works pretty well and easy to use. It just takes a little patience with the pitch, yaw, and roll pots. Once you have them set, quad flies very well.Little bit complicated to get working properly, but nice to fly when done properly. No self leveling feature, but good for training maneuvers and orientation. Nice and very cheap controller.
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
HK i86 User Manual download now [933kb] Tips montajes download now [3731kb] So simple 1 download now [170kb] No File Name download now [790kb] rus review download now [0kb] Manual_Rus download now [1176kb] HK i86 manual download now [933kb] i86 Stick Centering corrected download now [7811kb] No File Name download now [396kb] No File Name download now [933kb] No File Name download now [933kb]