HobbyKing Jet Pulso Motor a gasolina "Cabeça vermelha", com sistema de ignição

• Overall
• Quality
• Value

Very positive!

Feb 07, 2017

See http://www.rcgroups.com/forums/showthread.php?2027012-HobbyKing-Pulse-Jet/page46#post36813306

• Overall
• Quality
• Value

Customer Rated

Oct 16, 2016

I've read some critical reviews, but our experience has been very positive. Ours runs well on 96 octane pump gas in NZ. I'm writing this review to share what we learned about starting it because we had trouble initially. No need to increase jet size. Get a good fuel tank with a short (40 - 50mm) fuel line. Fill tank to the correct height per manual and ensure fuel line doesn't empty between bursts of compressed air. They need LOTS of pressure and once we realised that starting was easy. We have 200L compressor tank at 120psi. Made a fitting to seal gun nozzle directly to the spray bar. Spray, stop pop about 6 times to warm things up and then try a sequence of short bursts. Very, very noisy. You must have earmuffs, safety glasses and be ready to shut it off by pinching the fuel line after about 10 seconds. Wife, visitors, neighbours all utterly terrified. Awesome!

• Overall
• Quality
• Value

Customer Rated

Jun 06, 2016

we have been using this at school (Aviation High) and have found it to be a fantastic product to demonstrate the famous pulse jet. I have read some negative reviews elsewhere, but can only say that our jet works great. Lots of noise and heat, what more can you ask for. My only other comment would that the listed thrust of around 1.6kg would be pretty conservative. ours is bolted to a very heavy frame and then this was sitting on a 8 draw high tool chest. If we dont chock the wheels, it would sail off down the road. Very impressive

• Overall
• Quality
• Value

Customer Rated

Mar 30, 2016

Hi Chaps
Mine Runs very well on Gassoline/Petrol. Three things must be done Drill Fuel metering jet out to 1mm, Preheat the combustion chamber with a heat gun or blow torch, then PULSE the Air..... DO Not blow continuously this wil open the Petal vavle and blow away your mixture and deaden the firing sequence. I am running mine on 95 Octane Gassoline/Petrol (SA).
If in Doubt checl out this :- https://www.youtube.com/watch?v=MaIFK_85578 Bruce Simpson sorted itout nicely THANKS Bruce.....

• Overall
• Quality
• Value

Customer Rated

Jan 19, 2015

I receive my engine only on 6 days ( California) everything looks good, I tried to start it with 91 gasoline and a air from a big compressor 155 psi, , but nothing ,, the fuel going inside but not fire, I reduce the air flow by closing a little the air valve, and then start but after removing the air supply the engine died , I think the air pressure will be 25 to 30 psi, only and the fuel supply is too lean, the engine only work with the air blowing on the intake, I am going to drill the cooper gasoline tube the make it rich ,, I am happy with it, after fine tune will work right , ,,,Is loud , very loud,, and coming hot really fast,
I will write again after make it working good

• Overall
• Quality
• Value

Customer Rated

Jan 12, 2015

Wahnsinns Teile! Ich hab mir gleich mal 2 Stck mit Igniter und Accu gekauft ! Yeppa. Geliefert am am 05.12.14. Direkt komplett zerlegt ! Zum Glck! Denn die Ventile deckten die Bohrungen nicht richtig ab. Innen ist ein gaaanz kleines Loch und die Ventile rechts und links davon mssen exakt gleich weit vom Kalibrierloch entfernt seien ! Nun zum Sound ! Ihre Schwingfrequenz betrgt je nach Temperatur zwischen 220 bis 240 Zyklen pro Sekunde. Also extra Laienhaft verdeutlicht zwischen ((vergleichbar eines 2Takt Motors)) 13200 bis 14400 Umdrehungen pro Minute. Nun zum Lrm : Kein Vergleich zu alten groen Pulsos ! Vom Klang und Lautstrke klingen Sie wie ein 10 Kubikmotor an einer 11 X 7 Latte mit schlecht gedmpften Seitenschalldmpfer . Allenfalls 10ner ohne Dmpfer ! Also es geht so. Ich war sehr verwundert das Sie deutlich leiser waren als das was ich bisher kannte! Nun die hohe Schwingfrequenz machts. Nun zum anlassen : Selbst mit viel Kraft und Guter Luftpumpe ist es etwas schwierig. Mit einem Kompressor super easy . Auf meinem Prfstand habe Ich 20cm vor dem Kopf , Rechts und Links vom Pulso 2 WEMOTEC Mini Fans, ( beide Fans den Strahl Richtung Endrohr justiert ), um das Rohr beim laufenlassen zu khlen . Das funktioniert so gut das sich die Rohre bis jetzt kaum verfrbt haben. Ich hoffe da dies

• Overall
• Quality
• Value

Customer Rated

Dec 13, 2014

After my initial failure to start on gasoline I tried a 80/20 mix of methanol/nitromethane. SUCCESS!!! runs great!!!

The main jet was opened to 1/16 inch and body drilled out 3/32 inch, the cross holes were also opened out to 1/116 inch dia. (details from Web )

I made a very simple spark unit from a 12V car coil and a 12V relay wired as a "buzzer"powered by a 3s1p Lipo 3000mAH. This gave a fatter spark with higher frequency, the plug body was turned down to leave the centre electrode standing clear.

• Overall
• Quality
• Value

Customer Rated

Oct 03, 2014

OVER ALL THIS IS THE BEST MADE AND SLEEKEST PULSE JET MODEL ENGINE IVE SEEN FOR SALE SINCE 1960S

IF YOU WANT ANY OTHER PULSE JET IT WILL NOWADAYS BE A CUSTOM ORDER OR A VINTAGE USED DYNA JET OR OS ROCKET ENGINE AND THOSE DO NOT HAVE REPLACEMENTS AVAILABLE


THESE ENGINES ARE MOSTLY MADE FOR FREE FLIGHT AND CONTROL LINE PLANES BACK IN THE DAY......IT WILL BE NICE TO SEE SOME RC MODELS CREATED USING THEM....LOTS OF THRUST.....MY NEXT ONE WILL BE INSTALLED ON A 1/5 SCALE CAR TO SIMULATE A SALT FLAT RACER

• Overall
• Quality
• Value

Customer Rated

Apr 10, 2014

Hi all, just got the pulsejet and this is my review.

The box it came looked great and the engine where packed nicely.
The engine it self where very poorly welded, its supposed to be round but its more egg looking shape.

The ignitior box has a nice plastic frame/box but the components sucked, lasted for about 10 sec then it died. But im going to build my own igniter circuit and put it in the box.

But overall the engine starts. i used gasoline to start it with and after a fiew tries i got i running for about 20 sec and then turned it off by blowing with compressed air in the inlet valve. the reed valves looked ok after the run.

I am going to put up a youtube video of it running so check my channel out

TimmyEriksson is my channel name.

• Overall
• Quality
• Value

Customer Rated

Apr 05, 2014

Seems well made with good machining on the machined parts. The welding is great and while the main part of the Pulse Jet is two metal pressings which are welded together the overall fit is pretty good slightly out of round but owing tot he way that it's constructed quite OK.



Only thing I feel need improving is the Instruction Manual for the Igniter. These are for short duration and it needs to say that the unit has a limited life at full power and should only be used in very quick bursts with time between each use to allow the circuity to cool down and return to best effeminacy.



I'm perfectly happy with the unit which works great. Only real problem is I now have to finish off the model it's going into so I can take it out and fly it. Pity that the thing I'm building isn't a Model Plane but made from the Construction Drawings of the real thing so there is a lot of messing around fitting what's needed.