O ajuste de temperatura características HobbyKing Universal Sistema aquecedor e um sensor de temperatura para permitir o controlo da temperatura de 30 a 80 graus celcious. Com uma faixa de tensão de 7.4v a 12v o aquecedor pode ser alimentado por um 2s para lipo 3s. Adicione um a sua luva transmissor e voar em luxo neste inverno, aquecer os pneus em seu carro ou pré-aquecer a sua lipo no inverno ou mesmo verão para o melhor desempenho.
Pré-aquecimento de um pacote de Lipo para 30degC no inverno vai dar o seu modelo de um desempenho muito melhor, desde o início.
Entrada: 7.4v a 12v
Temperatura: 30 ~ 80deg Celsius
Sensor: LM35DZ - Precision centígrados sensor de temperatura
Almofadas de calor: 310x80mm
Amp Sorteio: 5.2A @ 12v
Conector de Entrada: 2 x Alligator Clips
Características do Produto
Peso ( g )
Always make your hands warm in winter while model controlvery good product! AplusplusI mounted all the components excluding the heating pads on a 5 inch by 8 inch quarter inch plywood mounted with HK wide blue velcro between the hand holds so as to keep the top of the glove well above the bottom of the glove. This helps keeping your hands off of the heating pads which are place to the sides of the bottom of the glove. This arrangement with the heaters in series on a 3S LiPo is a comfortable arrangement.This heater is fantastic if you use it correctly. Either use it with a 2S LiPo as received, or re-wire it so that the two heaters are connected in series and run it on 3S. This avoids the heating pads getting very hot as stated by others.
In series on 3S it takes about 2 amps when the LiPo is at storage voltage (about half discharged). This is sufficient on fairly cold days since in another review it stated that at 3S it used about 1100 mAh for 1 hour at -15 degrees C (5 degrees F) hence at an average of 1.1 amps, so 2 amps for the series connection is sufficient.
I chose to make allowances for even colder weather and replaced the four pin cable connector with a 10amp DPDT switch with a center off position (from Radio Shack). This allowed me to switch between parallel heaters and series heaters or off with a 3S LiPo. The heating power is about 120 watts for parallel and about 30 watts for series heater connections, and I only use the 120 watts for a quick pre heat of the glove. However if the temperature never goes below 5 degrees F (-15 degrees C) then you only need the series connection for 3S operationPerfekt fr kalte TageDraws 5,5 amps from 3S 2200mAh LiPo. Temperature sensor is installed into one pad only, but this is not an issue while pads are installed into similar coditions. Make sure you use separate LiPo low voltage buzzer to protect your battery.Great Heater nice and compact! Will be used throughout the winter months to keep hands/lipos/telescope lens warm and dew free. Have swapped the croc clips for a deansJust got mine the other day 10days to Canada is awesome !
I have bench tested it and so far looks and works awesome and a big they have pre installed the temp sensor already into one of the pads so Hobby King had listened way to Go HK !!For winter flying a good tool to bring/hold the bateries at ambient temperature. Recommended item.Very tiny box, it was astonished. I soldered a XT60 to it as replace of the one what came with it. It heats up very fast, I used 3S battery. Has to be careful never to turn it full scale. I use this in my glove box for the winter, awesome! Recommended!
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
CE Certificate download now [666kb] No File Name download now [400kb] Ih1K4LyjHY4.jpg download now [1.22Mb] Technical Specifications download now [28.50Kb]