Os servos HK Série Mi representam a próxima romper em alta tecnologia servo precisão. Usando indução magnética, ao invés de um potenciômetro, para um nível inigualável de precisão e desempenho.
Voltagem: 4.8V / 6v
Velocidade: 0,07 seg / 60deg (4.8V) - 0.06sec / 60deg (6V)
Torque: 4.50kg.cm (4.8V) - 5.50kg.cm (6v)
Tamanho: 40 milímetros x 20 milímetros x 39,2 milímetros
Peso: 52 g
Engrenagem Train: Full liga de titânio
Mi: indução magnética, utiliza um codificador rotativo magnético no lugar de um potenciômetro tradicional (inventado em 1877). leitores magnéticos rotativos têm uma vida mais longa e sofrem menos desgaste.
Características do Produto
Peso ( g )
Speed ( Sec / 60deg )
Torque ( kg) ( min. 0,01 kg )
Unit Weight (g):
A ( mm ):
C ( mm )
D ( mm ):
E ( mm):
F ( mm )
Very impressed with these servo. Precision and speed ist absolut great. Servohorns in standart and high torque from Blue Bird, Hitec and Futabe will fitt. GWS is to small.used them for my aileron, two on one long rudder. Wowe...what a speed and precisition. Geartrain is absolute high precition. Use them with a 2s LiFe and they are faster then my fingers........I'm running 8 of these on a 100cc Extra 330 through a 14 channel Futaba receiver and powered by 2x2100mah Turnigy Life batteries in parallel. 10 flights and no problems; these are the fastest servos I have ever used in 30 years of RC.Good, very fast servo for the price!Hey guys I have been running 2 of these servos now in 1/10 scale off road cars one in a short corse truck and one in a 4x4 buggy and I must say I am very impressed with the speed, accuracy and strength of these servos. They don't run hot at all the drain on the battery seems to be less than my previous servos (savox). I would recommend this servo to any one running 1/10 scale cars off road or on road. I would guess there is plenty of torque to run this in an 1/8 scale car as long as you DO NOT use 7.4V lipos unless you run them regulated. I have put probably 15-20 packs through my SC truck now and still going strong.i have one this things use for my tail servo in hk600gt very noise servo. and get warm my ubec is TURNIGY 5-7.5A (8~42v) HV UBEC for Lipoly..i use 2s lipo when i use 6 volt setup very noise, :(These servos work nice for HK600GT tail, fast and centering is very good. I like this better than my Align DS650 servo so far. Have only used for few weeks so can't comment on how well they hold up long term. You need to add large capacitor soldered to /- leads from BEC to receiver if your BEC is a switching type as most are. They will make lots of noise without it and could cause brown out, I used 3500uf 16volt from HK found in RX/TX accessories and have had no issues.5Kg y 0.06, es ideal para cola
I used this servo with UBEC 6V (6.2V) step down to 4.8V (my custom 2 diode step down). It not heat temperature = 41-43C in 5 minI used HK47002DMG powered by the TR-UBEC15 using a 2S set 5V (with step down for rudder) Temperature is 43-46C
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!