Jumper 218 Pro Corrida Drone (ARF)
O Jumper 218 helicóptero quad Pro é projetado com os entusiastas em mente. Este quad tem uma distância entre eixos de 218 milímetros O quadro é leve, mas muito forte, permitindo alto desempenho. Tornando-idéia para o voo FPV ou executar 3D. A sua instalação simples rapidamente você fica operacional e de vôo.
controlador de vôo Naze32 com OSD dá resposta rápida e confiável. A moldura inferior tem linhas de energia, interface de transmissor AV, interface da câmera e interface de energia construído em, bem como a placa de potência integrado (com conector XT60). Os braços têm uma linha de energia intergraded para os CES para parar cabos desarrumado. Para FPV o kit vem com uma câmera 600 TVL, com suporte ajustável, e um transmissor AV 5.8mHz 200mW. O trem de força incudes 1806-2280KV motores com BlHeli 20AESCs e 5040 hélices para dar-lhe um excelente desempenho. Construído em LEDs nos braços mostrar-lhe o caminho a percorrer.
Este quad é grande valor para o dinheiro e vai dar-lhe horas de entretenimento e diversão.
• Poderoso 1806-2280KV motores
• BlHeli 20A ESC, resposta rápida, aceleração suave
• 5040 Hélices (CW e CCW)
• placa de distribuição de energia intergraded e eletrônica controlador de vôo (com conector XT60)
• Naze32 sistema de controle de vôo com OSD, 32bit ARM micro processador para a velocidade rápida e resposta rápida
• controlador de vôo Cleanflight e Baseflight suportada
• Vem com brilhantes luzes LED para indicar a orientação de uma multirotor
• Construção forte (1.8mm quadro placas com a construção de múltiplas camadas, 3,2 milímetros para os braços)
Distância entre eixos: 218 milímetros
Controlador de vôo: Naze32 com OSD (baseflight, cleanflight)
ESC: 20A BLHELI
Brushless Motor: 1806-2280KV
Hélices: 5040 (2xCW e 2xCCW)
Transmissor AV (TX): 5,8 g / 200mW
Câmera: CMOS 600 TVL, Visual ângulo de 120 graus
Power Adapter: XT60
Peso: 328g (com câmera e AV transmissor sem receptor e bateria)
1 x Jumper 218 Pro
1 x Manual
bateria 1500-1600mAh 3S LiPoly
5-6 canal TX / RX
FPV Googles / screen
Nota: Não existem conhecido por ser cloanes baratos do Jumper 218 no mercado. As falsificações podem ser identificados pelo lago do fio traço vermelho (foto acima). As falsificações podem perder sinal de vídeo quando dado acelerador devido a este problema. Hobbyking só vende o mais recente Jumper 218 estoque Genuine Pro.
Características do Produto
Peso ( g )
like this little machine...runs ok. But I was - again - sick and tired with manual provided. Hobbyking really needs to get into business of INFORMING/GUIDING new quad customers decently in manuals. I have written this before with other products from hobbyking, but still we buy stuff that we by ourselves have to figure out. And with "Little technical" knowledge we really needs help...via small video etc. that explain all basic concerning installing etc., right from start with connecting what colour wire where and so on. It cannot be true that every time I buy something from HK I have to juggle around the internet for hours to find solutions for my new investments...Pros:
-robust and sturdy frame
-nicely made, good materials used
-very stable flight after some tuning
-flight time 8 min with 1500 mAh (no 3D, smooth flight)
-screws were getting loose and doped in flight. One must glue or fasten them.
-reconfiguration with computer requires jumpers switching each time (otherwise OSD stays off)
-motor power cables soldering was weak, they detached after hard landing
-there is no room for FPV transmitter inside frame. Installed below fuselage exposes it to damage
-lack of spare parts (I may be wrong, but I could not find them so far)Ok after lots of curisng and cussing heres my review. The FC isnt naze32 its a knock off which in turn is a knock off of Naza BUT it works the same its easy to configure. I had some issues i couldnt get power to my reciever or video this caused so much hassle and hair pulling eventually i stripped it all down and found the problem the 5v pin for video and reciever were bent over and squashed on the naze board ports. The other issue is it wont ARM unless i assign a switch which then causes me problems changing modes. So im currently flying in ACRO mode all time i will sort it eventually but its no biggy. Also locktite everything you can even the prop hubs ive lost two already and 2 of the screws came out during flight.This quad flies like a dream , so easy to fly The board is great with the built in osd .
Some concerns about the way its designed , too much integration for my taste and the esc should be in th arms not hogging all the real estate on the main body .. there is no where to place a receiver neatly in the frame .the manual is usless and dosent explain enough about the switches , and the supplied vtx lasted 3 mins before it died ..the whole quad smacks of proprietry style build and is too intergrated for my liking ..the only real plus is the control board with the built in osd , and the ability to change pids in the osd menu .Nettes Gert. Die Schrauben sollten alle mit Loctite gesichert werden. Bei der Gelegenheit kann man gleich die zwei Platinen der Arme mit Epoxy verkleben. Dadurch wird alles viel stabiler. Im FC muss man oneshot=on und looptime=2500 einstellen, sonst vibriert es. Der Video-Sender wird extrem hei. Das geht nicht lange gut. Entweder 4 Siliziumdioden oder einen Spannungsregler fr 7V davor (nach TE383 suchen) (Stromaufnahme ist ca. 300mA). Kamera ist nicht toll. Aber fr den ersten Versuch ausreichend. Flugleistung ist berzeugend.Although this is supposed to be a ready-to-fly product the quality control completely screwed that up.
None of bolts were fixed with locktite, which meant a motor got lose and tore off from the solder point the first minute of flight. Even though the motors and frame have 4 mounting holes, only 2 were used per motor. Pretty much all the bolts in the front half were lost as well.
I would not recommend this to a beginner and a pro would not bother of course, the performance of this quad is below standard and replacing arms, etc requires complete disassemble.
The integrated voltage regulator on the power distribution board is low-quality and the PCB traces are to thin to handle the current. So it got fried almost instantly.
So now I'm stuck having to order the replacement parts from the international store since the EU does not stock those.I have bought this , Nice manual ,Good product! I disconnnected the LEDS they make flighttimes shorter, i used my 3D printer to make a plate to lift the battery above my reciever. Now i can fit my gopro. It is 570g With gopro 4 , 3s 1500mah 40c battery. I get around 6 min flighttime. If somone is interested in the CAD file of the upgrade part, please feel free to contact me.Hi have purchased this fpv racer two weeks ago.
PRO: prize, osd included with Star Power FC (useful for monitoring voltage).
CONS: No SBUS support, no oneshot 125 support. It's necessary to change dip switch setting to program or fly modes.
Note: I use baseflight 2.4.0. baseflight firmware version, with 2.5 or above the fc doesn't arm motors.I gave it one star overall for the lack of information supplied with it. It comes with a whole bunnch of individual wires for , I'm guessing the receiver, but no instruction manual. The stupid booklet that comes with it only tells you how to program the controller, where in the heck the wires go to and to WHAT is a mystery.BOO :(
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
Westerlund 32 Flight Controller with OSD download now [104kb] Video TX instruction manual download now [85kb] RX Connections download now [645kb]