New Items Forum
Registar

Total Price

0,00 €

Carrinho 0 Carrinho 0 Loading...

Kingduino Fio ATmega328P microcontrolador

Kingduino Fio ATmega328P microcontrolador

Discontinued Product

Please continue searching for a similar product.
SKU:
381000054
WANT FREE SHIPPING? Click here to find out more!

O Arduino Fio é uma placa de microcontrolador baseado no ATmega328P funciona a 3.3V e 8 MHz. Dispõe de 14 pinos digitais de entrada / saída (dos quais 6 podem ser usados ​​como saídas PWM), 8 entradas analógicas, um ressonador on-board, um botão de reset e buracos para a montagem de pin headers. Ele tem conexões para uma bateria de polímero de lítio e inclui um circuito de carga ao longo do USB. Uma tomada XBee está disponível na parte inferior da placa.

O Arduino Fio é destinado para aplicações sem fio. O usuário pode enviar esboços com um um cabo FTDI ou placa de fuga. Além disso, usando um adaptador USB-to-XBee modificados tais como XBee Explorador USB, o usuário pode carregar desenhos sem fio. A placa vem sem cabeçalhos de pré-montado, permitindo o uso de vários tipos de conectores ou de solda directa de fios.

especificações:
Microcontrolador: ATmega328P
Tensão de funcionamento: 3.3V
Tensão de entrada: 3.35 ~ 12V
Tensão de entrada para carga: 3,7 ~ 7V
Digital I / O Pins: 14 (dos quais 6 fornecer saída PWM)
Pinos de entrada analógica: 8
Corrente DC por I / O Pin: 40mA
Memória Flash: 32KB (dos quais 2 KB utilizado por bootloader)
SRAM: 2 KB
EEPROM: 1 KB
Velocidade do relógio: 8MHz
Dimensões: 65x28x12mm
Peso: 8,2 g

* Nota: Este não é um produto de marca original Arduino.

  • SKU 381000054
  • Brand -
  • Capacidade ( mAh) -
  • Peso 19.0000
  • Comprimento 75.00
  • Largura 30.00
  • Altura 45.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

I'm not using this with an xBee but a WiFLY board from Roving Networks which gives you full Wi-Fi connectivity.



The board appears identical to the reference design, soldering of the headers and xBee socket is rather poor but nothing that can't be fixed with an iron.



Lots of sticky flux residue on the board but again cleaned in a minute.



it will charge the 1S LiPo anywhere from 3-6v input and a red LED indicates charging, turning off when finished.



If you wish to program this while the WiFLy is connected you will have to do two things.



1. send the command "set sys trigger 0x20" to the module followed by "save"



2. solder a switch between pin 4 of the xBee socked and 3.3v.



When the switch is closed it will put the module into sleep mode and you can program your arduino freely!



When ready to run again set the switch back to off.



Note: if you intend to use hardware debuging with a dragon or jtag-ice you will not need to remove C3 as you would on a Arduino Uno, just unplug the ftdi from the port.



Phew, that was a rambling diatribe!



TL;DR version

Very good board, very good price, a few soldering issues.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I'm not using this with an xBee but a WiFLY board from Roving Networks which gives you full Wi-Fi connectivity.



The board appears identical to the reference design, soldering of the headers and xBee socket is rather poor but nothing that can't be fixed with an iron.



Lots of sticky flux residue on the board but again cleaned in a minute.



it will charge the 1S LiPo anywhere from 3-6v input and a red LED indicates charging, turning off when finished.



If you wish to program this while the WiFLy is connected you will have to do two things.



1. send the command "set sys trigger 0x20" to the module followed by "save"



2. solder a switch between pin 4 of the xBee socked and 3.3v.



When the switch is closed it will put the module into sleep mode and you can program your arduino freely!



When ready to run again set the switch back to off.



Note: if you intend to use hardware debuging with a dragon or jtag-ice you will not need to remove C3 as you would on a Arduino Uno, just unplug the ftdi from the port.



Phew, that was a rambling diatribe!



TL;DR version

Very good board, very good price, a few soldering issues.

Customer files
Arduino Fio Schematic Download [51]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!