Kingkong Fly Egg 130 Camera Racing Drone with Piko BLX FC, 4in1 ESC, VTX, Camera, Rx Ready

The Kingkong Fly Egg 130 is an eggcellent (excuse the pun!!) small fun fly or racing drone that will give you hours of enjoyment in a very small package. The Fly Egg 130 is extremely durable and has great crashability due to its 2.5mm carbon base frame and arms and the egg shaped side frames that are made from 7075 aviation grade aluminum. Couple this with durable props, whip antenna and a light weight and you would be hard pressed to break it in a crash, it is virtually indestructible.

This version is receiver ready and comes with the following, a 4 in 1 10A 2/3S A10 ESC which supports MULTISHOT, ONESHOT and DSHOT, a PIKO BLX flight controller with the latest Betaflight firmware and a 800 TVL 150° camera with adjustable tilt angle. Also included is 4 x XT1104-7500Kv motors which are fully enclosed, 1 x 7.4v 550mah lipoly battery, 2 sets of 2840 props, 1 set yellow and 1 set white and a set of prop guards. Supplied as well is an onboard low battery warning buzzer, rear addressable LED lights, USB cable for re-flashing, a tool for undoing the props, spare rubber strap for the battery and 4 x motor protection seats. The Fly Egg 130 also comes with a 16ch 5.8GHz 25mW or 100mW switchable VTX which comes preset to 25mW, to change this to 100mW it does require a small ampount of soldering. All in all this is a great little package that will have you flying in minutes at a price that is extremely affordable.

Features:
• Receiver ready
• 7075 aviation grade aluminum side frames
• 2.5mm carbon base frame and arms
• Extremely durable
• Small and lightweight
• Flexible whip antenna
• PIKO BLX flight controller with latest Betaflight firmware
• A10 4 in 1 ESC that supports MULTISHOT, ONESHOT and DSHOT
• 16ch 5.8GHz 25mW/100mW switchable VTX
• Adjustable camera angle
• Fully enclosed motors
• Low battery warning buzzer
• Rear LED lights
• Prop guards

Specs:
Model: Fly Egg 130 Rx Ready Racing Drone
Wheelbase: 130mm
Fly Tower: 20 x 20mm
Flight Controller: PIKO BLX with Betaflight firmware
ESC: A10 4 in 1 10A
Motors: 4 x XT1104-7500Kv brushless motors
Propellers: 2840
Camera: CM231 800TVL with 150° lens
VTX: 16ch 5.8GHz 25~100mW switchable (see list of transmitting frequencies below)
Battery: 7.4V 550mAH 80C
Weight: 77.5g (without battery and receiver)

VTX Transmitting Frequencies:
Band 1: 5658 / 5705 / 5790 / 5806MHz
Band 2: 5695 / 5740 / 5820 / 5843MHz
Band 3: 5732 / 5760 / 5860 / 5880MHz
Band 4: 5769 / 5780 / 5917 / 5945MHz

Included:
1 x Kingkong Fly Egg 130 Rx ready racing drone
1 x 7.4V 550mAH 80C lipoly battery
4 x Spare propellers
1 x Propeller removing tool
4 x Prop guards
1 x Spare battery retaining band
4 x Motor protectors
1 x USB cable (for updating Betaflight firmware)
1 x User manual

Required:
4ch or more transmitter and micro receiver
Suitable lipoly battery charger
FPV goggles or monitor with 5.8GHz receiver

Note: User manual available under the "Files" tab.