Este modelo é quente!
Uma máquina de cabeça-girando EPO 1.4m 3D; este modelo em larga escala certamente irá atrair uma multidão em qualquer clube e exigir o respeito total entre os pilotos em 3D em todo o mundo.
O esquema distintivo e escala é ideal para a orientação. A MX2 é grande para um modelo de EPO e parece quase o dobro do tamanho, uma vez que está no ar. É uma explosão de voar e é muito 3D capaz!
O poderoso, spinning 36-48 de motor pré-instalado que grande & escala de 3 prop lâmina dá muita pressão para o mais selvagem de maneouvers, e os servo pré-instalados de são certamente até o trabalho. superfícies de controle de tamanho generoso combinadas com peso leve garantir isso é um verdadeiro artista, bem como um torneiro cabeça. Prático, bem como fácil no olho, as asas são destacáveis para fácil transporte, uma grande copa garante fácil acesso a bandeja Lipoly, parafusos da asa e assim por diante.
Envergadura: 1400 milímetros
Comprimento: 1.290 milímetros
Voar Peso: 1900g
Asa Loading: 50g / dm2
Motor: 42-48 Brushless Outrunner
ESC: 70A w / BEC
Servo: 2 x 9g, 2 x 17g
Manual de instruções
Sua própria 4 ~ 6 Canal TX / RX
Bateria 2200mAh 4s Lipoly
Características do Produto
Peso ( g )
Motorsize ( diam -ou- cc)
SaleWeight ( g )
Frame / PNF / RTF (mm)
IC / 2: Elec:
Capacidade ( mAh):
This is a very well made model and flies like a dreamIch habe versucht dieses Modell zu einem vernftig fliegenden Flugzeug zu machen: leider ohne Erfolg, das Merial taugt einfach nicht. Es ist extrem empfindlich, bei etwas hrteren Landungen bricht es sehr leich komlpett durch. Die Flgelbefestigungen sind absolut untauglich, etc, etc. Nach viel Stunden und Reperaturen (und zugekauften Ersatzteilen) habe ich mich genug gergert und werde das Modell "entsorgen", auch wenn es am Boden immer noch sehr gut aussieht.
Sorry HK, ich bin sonst von vielen eurer Produkte sehr angetan!I got this as a gift for my son he is 42. So this is not for son who is a good modler. The instructions are useless and pictures are even worse. The small parts bag was missing many items. The paint on one single panel was bobbles no paint. Flying is good but the CG is very important. No Where in instructions is it providedNice looking model, pity the quality is crap, tail wheel a pain ,control rods to long, elevator rod to long by 15mm , wrongly labelled items. poor manual, screw hols filled with glue, wheel hubs have to be drilled out to allow wheel to spin , tight on bolt so when wheel turns it follows thread and locks up. rudder needs extra hinge, hope it fly's awesome after all the mods and work to get it built.Im going to be as real as possible on this plane. Stock setup will not 3D , the plane is too heavy for this. Flew mines today with a 2650 4s and when she got airborn as soon as i pitched the plane she wanted to snap on me (Wing tip stall) then i landed the plane and tried a lighter battery this time using a 2200 4s , Did much better but still had the snap problem when pitching the plane. Don't Believe what you see in the video in the description of this plane because it will not perform that way with some modifications.
1ST thing i would do is replace the wing spare with a lighter one because thats one problem for the wings. Weight is every important in a aerobatic plane. 2nd Replace the landing gear with carbon fiber lighter ones , these add extra weigt to the plane. 3rd Change out the tires and buy lighter ones. Those 3 items i mention should be replaced to make this plane lighter and fly better.
The stock motor and prop are good enough for this plane to do 3d with , did some testing before i took it out to the field. Other than that it flys pretty good , takes off fast. Just with they would make some changes to the plane and make it lighter.The tail piece on this one may arrive warped. The landing gear holes in the bottom of the fuse don't line up and have to be re-drilled before the landing gear can be re-attached. The landing gear wheels will bind-up and you may need to remove the wheels and remove some foam to allow the wheels to spin freely. The tail wheel arm will likely hit the tail/rudder and may need to be bent to fit. Mine snapped, even with heating first. I had to fabricate a new piece in the correct shape. It's easiest to do this with 2mm aluminium. The motor mount screws are over-tightened and not holding well in the wooden brace. You may need to swap them out for larger screws. The motor has no loctite on the bolts. You should unbolt it all and loctite it all in properly. The servos that come with it are not as advertised. They are full size units (41x20x37) of unknown make/model. They have lots of play and will need to be replaced before you fly, with better quality units, as the rudder/elevator will be too floppy.
Not a good product, but with some loving you can get it into reasonable shape.Great Plane Poor Prop Adapter. Build own one from DURALUMINIUMThe good bits.... Looks fantastic in the air!!, large size and hobbyking are selling the high powered '3D' version with 4258 motor and standard size servos for the elevator and rudder. It is also a very simple assembly.
The bad bits.... mine crashed on the maiden flight after 10 seconds when the stock ESC burnt out. It had not even been past around 60pcnt throttle (it takes off very easy). Was not nice watching a plane that I had bought for its appearance snap in half. An aileron servo also died in the crash, on a wing that was not impacted.
The flying.... I bought this as a nice looking sport flyer, and after spending a weekend repairing it and replacing the ESC, spinner and propeller I got it in the air i confirmed it is an OK sport flyer. Only handling flaws are snapping out of tight loops due to not having enough hinge points in the ailerons, and a relatively high stall speed. It also needs quite a bit more power, probably a 5s upgrade would do it, the motor looks like it could easily take it as it was still cool after flying with 4s. Note I an currently flying with a 13 x 4.5 slow fly 2 blade wooden prop. As far as 3D flying goes.... forget it, I have EPP 3D planes that this isn't even in the same galaxy with, but I knew that before I bought it.Great plane for the money. instructions could be better and so could the accessory pack, but any decent modler should be able to over come these problems with ease, its not rocket science.
any way amazing to fly im using a 2200 4s to keep wait down. HK You've done it again.Well flew this for the first time last weekend.
Several problems with it.
1 The motor mount embedded in the foam is not secure so it moves, this requires glueing in with a spacer installed under the cowl from underneath.
2 The elevator servo was shuddering and never centered ever.
3 The spinner or prop adapter is badly out of balance.
It flew great but doesnt do 3d with a 4s1p 3300 pack, i will try a 4s 2200 pack when the replacement adaptor arrives.
Was tempted to use a normal 2 bladed prop but would just look wrong
Well worth the money just needs better QC with supplied setup
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
No File Name download now [22kb] No File Name download now [18kb] 537502183X139867X26.pdf download now [18kb] Better manual with high res pics download now [5401kb] mx2 compatible esc manual download now [24kb] MX2 Manual download now [2265kb] wheel download now [380kb] WING SCEWS download now [2697kb] WING SCEWS 2 download now [2760kb] WING SCEWS 3 download now [2784kb] No File Name download now [209kb] No File Name download now [24kb] programming of esc download now [24kb] Mx2 Compatible esc Manual download now [24kb]